manualshive.com logo in svg

Seagull EP PC-9, Assembly Manual, Page: 9 / 14

Share
Download
Seagull EP PC-9 Assembly Manual Download Page 9

www.seagullmodels.com

9

!

5) Slide the vertical stabilizer back in

place.  Using a triangle, check to ensure that
the vertical stabilizer is aligned 90º to the hori-
zontal stabilizer.

90º

Vertical

Stabilizer.

Horizontal

Stabilizer.

!

 

4) Remove the stabilizer.  Using a mod-

eling knife, remove the covering from below
the lines you drew.  Also remove the covering
from the bottom edge of the stabilizer and the
bottom and top edges of the filler block.  Leave
the covering in place on the sides of the filler
block.

When cutting through the covering to re-

move it, cut with only enough pressure to only
cut through the covering itself.  Cutting into
the balsa structure may weaken it.

! 

6) When you are sure that everything is

aligned correctly, apply  C/A glue to fix them.

   

Attach the micro control connector to the

servo arms. Be sure to use the lock tie but it
could free rotation .

SERVO ARM INSTALLATION.

Lock tie.

   Control horn install as same as method of
aileron wing. See pictures below.

 CONTROL HORN INSTALLATION.

Pen.

Remove covering.

C/A glue.

Summary of Contents for PC-9















Reviews:

No comments