manualshive.com logo in svg

Seagull EP PC-9, Assembly Manual, Page: 2 / 14

Share
Download
Seagull EP PC-9 Assembly Manual Download Page 2

PC9-

EP

.

                                       

                                      Instruction Manual.

2

INTRODUCTION.

   Thank you for choosing the 

EP

-PC9 ARTF by SEAGULL EP. The 

EP

-PC9 was designed with the

intermediate/advanced sport flyer in mind. It is a  semi scale  airplane  which is easy to fly and quick
to assemble. The airframe is conventionally built using balsa, plywood   to make it stronger than the
average ARTF , yet the design allows the aeroplane to be kept light. You will find that most of the work
has been done for you already.Flying the   

EP

-PC9 is simply a joy.

   This instruction manual is designed to help you build a  great flying aeroplane. Please read this
manual thoroughly before starting assembly of your   

EP

-PC9. Use the parts listing below to identify

all parts.

WARNING.

    Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.

   If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C
supplier and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
procedures designed to help the new pilot on his way to successful R/C flight. They will also be able
to advise on any insurance and safety regulations that may apply.

ADDITIONAL ITEMS REQUIRED.

! 

Motor: Himark outrunner

                 C3522-990

!

Radio with four  sub-micro servos.

!    

Speed control: 35A to 45A.

!

Battery: Awesome Power battery

11.1V 2200 mAh - 11.1V 3200 mAh.

             Himark outrunner
                 C3522-990.

Speed control:
SJ Conquest 35 or 45 amp.

Awesome Power battery
   11.1V 2200 mAh - 11.1V 3200 mAh.

Summary of Contents for PC-9















Reviews:

No comments