Seagate BARRACUDA 2LP Product Manual Download Page 57

Page: 57 / 102

Barracuda 2LP Product Manual, Rev. D

10.0

Option/configuration headers

This section describes how to configure Barracuda 2LP drives using the
option headers on the drives. These option headers may be used to
customize many functions of the drives for your particular system.

10.1

Drive ID/option select headers

The headers described in this section enable you to configure the drive to
meet specific functionality requirements.

To configure N/ND drives, see Section 10.1.1.
To configure W/WD drives, see Section 10.1.2.
To configure WC/DC drives, refer to Section 10.1.3.

10.1.1

ST31250N/ND and ST32550N/ND configuration

Figure 19 illustrates ST31250N/ND and ST32550N/ND jumper connectors.

ST31250N and

ST32550N

J1 Connector

ST31250ND and
ST32550ND
J1 Connector

SCSI ID = 1

SCSI ID = 2

SCSI ID = 3

SCSI ID = 4

SCSI ID = 5

SCSI ID = 6

SCSI ID = 7

Remote
LED connector
Spindle sync
cable connector

Pin 1

Pin 2

Pin 1

Reserved

Ground (cathode)
Positive (anode)
Spindle Sync Reference

Spindle Sync Ground

SCSI ID = 0
(default)

(front view of J4)

Pin 2

Disable Parity

Write Protect

Pin 1

Enable
Motor Start

Pin 2

Delay
Motor Start

Term. power from
drive (default)

Pin 1

Pin 2

ST31250ND and
ST32550ND

ST31250N and
ST32550N

Term. power to
SCSI Bus (default)

Term. power to
SCSI bus
Term. power from
SCSI bus
Term. power to
SCSI bus and drive
Enable SCSI
terminator (default)

Reserved

Pin 1

Pin 1 End

Pin 1

Figure 19. ST31250N/ND and ST32550N/ND jumper connectors

Summary of Contents for BARRACUDA 2LP







































































































Search results

Summary of Contents for BARRACUDA 2LP

Reviews:

Related manuals for BARRACUDA 2LP

Brands by name

Popular brands

Seagate BARRACUDA 2LP, Product Manual

Search results

Summary of Contents for BARRACUDA 2LP

Reviews:

Related manuals for BARRACUDA 2LP

Brands by name

Popular brands