manualshive.com logo in svg

SEA SLIDE DG R2F, Manual, Page: 19 / 32

Share
Download
SEA SLIDE DG R2F Manual Download Page 19

RADIO TRANSMITTER SELF LEARNING

WITH «UNI» RECEIVER ON CONTROL UNIT 

!

         WARNING: Make the radio transmitters programming before you connect the antenna and 
insert the receiver into the special CMR connector (if available) with turned off control unit. With 
RF UNI and RF UNI PG module it will be possible to use both Coccinella Roll Plus

 

transmitters and 

radio transmitters with fixed code. The first memorized radio transmitter will determine the type of 
the remaining radio transmitters.

 If the receiver is a 

Rolling Code

, 

press twice

 the button of the radio 

transmitter that you want to program to memorize the first TX. In the case of 

transmitters with fix code

 it 

is necessary 

to press 1 time

 the button of the transmitter you want to program to store the first transmitter.

Notes:

- Enter radio transmitters learning only when the working cycle stops and the gate is closed.
- You can store max. 2 of the available 4 functions. If the control unit receives a code which was already 
associated to another function it will be updated with the new function. 

TABLE EXAMPLE

Transmitter 

button

Memory 

location

Serial 

number

Customer

MENU

SEA

SET

MENU

SEA

SET

MENU

SEA

SET

UP

MENU

SEA

SET

MENU

SEA

SET

UP

MENU

SEA

SET

MENU

SEA

SET

MENU

SEA

SET

MENU

SEA

SET

MENU

SEA

SET

UP

MENU

SEA

SET

MENU

SEA

SET

UP

MENU

SEA

MENU

SEA

SET

MENU

SEA

SET

SET

START

PARTIAL 

OPENING

STOP

DELETE A

TRANSMITTER

0

OK?

OK

CLEAR

MEMORY

OK

PRESS

BUTTON

STORED

STORED

STORED

PRESS

BUTTON

PRESS

BUTTON

If you want to program the 

PARTIAL OPENING START 

as second channel

If you want to delete 
a  single  transmitter

If you want to delete 
the  whole  memory 

Press the 

button of the 

transmitter 

to be stored 

Press the 

button of the 

transmitter 

to be stored 

Select with 

UP or DOWN   

the memory 

location 

to be deleted 

and press OK

Press the 

button of the 

transmitter 

to be stored 

If  you  do  not  want  to  execute  the 
cancellation, press UP or DOWN   to 
return to the 2-TRANSMITTER menu

Confirm the cancellation

If  you  want  to  program  the
UNLOCH as second channel

MENU

SEA

SET

MENU

SEA

SET

UP

MENU

SEA

SET

STORED

PRESS

BUTTON

Press the 

button of the 

transmitter 

to be stored 

If you want to program the

STOP as second channel

OK

for 10 s.

MENU

SEA

SET

OK

TRANSMITTERS

OK

MENU

SEA

SET

If  you  want  to  exit  the
2-TRANSMITTERS menu

END

MENU

SEA

SET

OK

UP

OK

OK

OK

OK

OK

Menu output

RF UNI

16 USERS 

Whitout memory

800 USERS 

With additional memory MEM

RF UNI PG 100 USERS

 Fixed code

800 USERS 

Roll Plus

RF UNI PG 800 UTENTI 

Fixed code

800 UTENTI 

Roll Plus

New model

Old Model

1

2

3

4

0
1
2
3

UNLOCK

MENU

SEA

SET

MOVE TO

EEP

UP

If you want to move the tran-
smitters stored on the control 
unit  to  the  external  memory 
EEPROM  (only  if  inserted 
and with FIX receiver in use)

OK

OK

MENU

SEA

SET

OK

MENU

SEA

SET

ERROR

The transfer was successful

The transfer was not successful

International registered trademark n. 2.777.971

19

Summary of Contents for SLIDE DG R2F

































Reviews:

No comments