background image

EN

 

General safety Instructions 

Danger, electric shock 

  Danger, hot surface 

It is mandatory to read this manual carefully before installing or using the product.

If the product is not installed and used as described in this manual the product cannot be considered
safe, so it could damage people or animals.

Installation and maintenance: 

The product must be installed only by qualified personnel.

Make sure that the batteries in use are compatible with the product by checking the battery type, the

nominal voltage and the charging voltage on their data sheet.

Make sure that the battery room is properly ventilated as indicated in the battery installation manual.

When connecting the battery, sparks can occur which can damage the operator's retina.

When the photovoltaic module is exposed to the sun it generates voltage. If the panel has voltage

Voc> 50V it is mandatory to use isolating gloves to protect the installer from electric shock.

For battery maintenance refer to the battery maintenance manual.

The product cannot be repaired by the user or by the personnel performing the installation; it must

not therefore be opened or left working with the panel open.

Do not install the product in a place where gas or dust explosions may occur.

Protect cables with suitable fuses from the short-circuit, in particular it is mandatory to place a fuse of

adequate current on the battery cable as close as possible to the positive battery terminal.

Warranty 

The defective product must be returned to 

SEA S.p.A.

 for assistance, at the expense of the customer, along with a copy of 

the sales invoice, both for repairing and guaranteed replacement. The costs of re-installation of the material will be borne 

by the customer. Warranty  does  not  cover  Products  that,  according  to  our  discretion,  are  defective  owing  to  natural 

wear,  have  failures caused  by  malpractice  or  negligence  of  the  customer,  by  incorrect  installation,  by  tampering  or 

interventions that are different from the instructions supplied by us. Warranty is void if damage is also caused by: 

- transport and/or bad storage of the product. 

- force majeure or catastrophic events (frost for temperatures < -20°C, fire, flooding, lightning, vandalism, and so on). 

All the above guarantees are the sole and exclusive agreement which supersedes any proposal or agreement whether 

written or oral

 

and any other communication made between the producer and the purchaser with respect to the above. 

For any dispute the jurisdiction is 

Teramo 

(Italy).

  

Disposal of waste 

SEA  S.p.A., 

in  accordance  with  Law  No.  151  25/07/05,  informs  the  buyer  that  this  product,  once 

divested,  must  be  delivered  to  an  authorized  recycling  center  or,  in  case  of  purchase  of  equivalent 

equipment, it may be returned at no cost to the distributor of the new equipment. Penalties for those 

who get rid of an electronic waste will be used by individual municipalities. 

Summary of Contents for E-SUN PLUS BOOST













Reviews: