Sea & Sea MDX-PRO D700 Instruction Manual Download

Page: 29 / 30

Specifications

* The specifications and appearance are subject to change without notice.

Compatible

camera

Nikon D700

Controls

Construction

Body: Corrosion-resistant aluminum alloy

Depth rating

60 m (200 feet)

Dimensions

Approx. 227 (W) × 201 (H) × 142 (D) mm

(9.08× 8.04 × 5.68 inches)

Weight

Approx. 2200 g (4.84 lbs.) (housing only)

Accessories

Power switch, Shutter lever, Exposure compensation

button, Exposure mode button, Sub-command dial,

Focus / Zoom dial, Focus-mode selector dial, Release

mode dial, Release mode dial lock release button,

White balance button, Image quality button, ISO

sensitivity button, Metering selector dial, Main command

dial, AF-ON / AE/AF lock lever, Multi selector, Info

button, AF-area mode selector dial, Delete button,

Playback button,

Menu button, Protect button / Help

button / Info button, Thumbnail / Playback zoom out

button, Plyaback zoom in button, OK button

Silicone grease, O-ring remover, Attachment tool,

Housing body cap, O-ring maintenance manual,

CR2032 lithium battery (for leak sensor, preinstalled

into battery compartment), Instruction manual (this

manual)

E-28

Summary of Contents for MDX-PRO D700































Search results

Summary of Contents for MDX-PRO D700

Reviews:

Related manuals for MDX-PRO D700

Brands by name

Popular brands

Sea & Sea MDX-PRO D700, Instruction Manual

Search results

Summary of Contents for MDX-PRO D700

Reviews:

Related manuals for MDX-PRO D700

Brands by name

Popular brands