olo
s
d
c o
ete
t r
t st
r
e e
s
®
Quick Start Guide to the
range of detector test equipment
Solo
Solo
330 Aerosol Dispenser
Solo
Solo
100 and
108 Telescopic Access Pole
Solo
A4
Smoke Detector
Tester
Solo
C6
CO Detector
Tester
Solo
A7
Detector
Duster
3
4
Unscrew and remove
retainer cup.
Place aerosol canister
into cup.
Replace retainer cup and
screw upwards. Adjust until
aerosol activates and unscrew
slightly.
Insert the
330 into
pole. Place
330
over the detector and press
upwards to activate the
aerosol (1 second burst).
Solo
Solo
Solo
If the detector has not
responded in 10 seconds,
repeat the test every 10 seconds.
Number of total sprays should
not exceed 5. If the detector fails
to activate, check equipment and
retest. If the detector does not
activate it will require further
investigation.
To prevent the possibility
of the aerosol discharging while in
transit, loosen the retainer cup by
unscrewing 2 full turns.
TIP
Maintenance
Excess liquid
deposits may be experienced
following extended periods of use.
To clean, use a lint-free cloth.
Wash the cup with a mild
detergent in warm water and dry
thoroughly.
Designed to be used only
with
330 (332)
dispenser.
Solo
IMPORTANT
Read the instructions and
warnings before use and
dispose with care.
Designed for handheld use only.
Use a
200 removal tool to
remove and clean high-mounted
detectors.
Solo
IMPORTANT
Read the instructions and
warnings before use and
dispose with care.
5
2
3
Twist to lock button.
100: 4 sections
108: 2 sections
Solo
Solo
Insert
tool into pole.
Solo
Solo
100
Solo
101
Solo
332 Aerosol dispenser
available for larger detectors.
1
2
1
Extend the
pole.
Solo
Solo
423/4 Heat Detector Tester
Solo
200 Universal Removal Tool
1
SAFETY INFORMATION
Attach power cable, secure
clip, and if required, add
optional extension cable.
Insert the tool into
pole.
Solo
Connect to power and press
switch. Place over
detector.
ON
4
If detector does not
activate within 1 minute
it may be faulty.
423 (110v)
424 (230v)
Fitted with a thermal cut-out
protection system.
Solo
Solo
DO NOT TOUCH
METAL GRID.
DO NOT BLOCK AIR
VENTS.
NO USER SERVICEABLE
PARTS.
Pull and twist the Tri-grips
to adjust for different
detector sizes.
When inserting into a
pole, locate lower button for
access to detectors at angles.
Solo
When inserting into a
pole, locate lower button for
use vertically.
Solo
Grip detector, twist and
pull down to remove.
1
2
3
1
2
3
4
A
101 1.1m extension pole
can extend the
100 and 108
telescopic pole, or may be used by itself
with the
range of tools.
A maximum of 3 extension poles is
recommended.
The Solo poles can be
cleaned with mild detergent in warm
water and a soft lint-free cloth.
Lubrication is not necessary.
The use of Personal
1
Protection Equipment is recommended
when using tools at height.
Solo
Solo
Solo
Tip
Maintenance
Warning
Solo
461 Cordless Heat Detector Tester
Solo
760 Battery Baton Charging
4
Insert a charged battery
baton into the tool and pole.
Ensure correct
1
orientation when inserting
battery baton into tool and do
not use undue force to insert.
Caution
Press the red switch to turn
on. LED illuminates green.
Flash at slow rate indicates
normal STANDBY mode.
Position the latch and place
over detector.
The tool will automatically start testing
when infra-red beam in cup is broken.
The green LED will flash faster. Hold in place
until the alarm is activated*. When the detector
alarms, remove the tool from the detector.
It will revert to standby mode (slow flashing
green LED), and the internal blower will cool
the heating element for a few seconds. After
testing, switch off at red switch to preserve
battery baton life.
Connect charger to power
outlet or lighter socket in
vehicle using mains lead
supplied or the umbilical DC
connecting lead. Power LED
will illuminate.
1
Do not attempt
to use or charge the battery
baton if either the charger
unit or the battery baton
connection point are damaged.
Warning
Connect battery to charger.
Fast Charge LED will illuminate.
When battery baton is fully
charged, Fast Charge LED will
extinguish. Trickle charge LED
will illuminate.
International power outlet cables are
available from your supplier.
Ideally, fully discharge battery baton
in normal use before recharging.
Tip
(*If the detector fails to activate it may be faulty. Insert a
replacement detector and test again)
Trickle charge
Fast charge
Trickle charge
Fast charge
1
2
3
1
<90min.
2
Tip
Ensure the
detector rests
firmly on
platform.
1
Remove battery baton when not in use.
Caution
2
Designed to be used only for
testing CO Detectors with
Functional Speed-Up
Test Feature.
IMPORTANT
Read the instructions and
warnings before use and
dispose of with care, even
when empty.
C6
CO
Do not use on
1
any other type of CO detector,
or with any type of aerosol
dispenser.
Caution
Insert straw into the nozzle.
Apply the gas using the straw
to the entry port of the
detector.
solo
detector
testers
TM
