background image

P:\INST INSTRUCTIONS\EXIT DEVICES\INST-S6200       Rev A       04-22       Page 4

“A”

Hinge Stile edge of door

Mark mounting
holes thru end
cap bracket after
device is leveled.

Mounting 
Bracket

Chassis

End cap 
bracket

Figure 2

VIEW “B”

Insert Trim Actuator Shaft
Into Device Cam

*

*

SECURITY DOOR CONTROLS   ■   WWW.SDCSECURITY.COM

[t] 800.413.8783  ■  805.494.0622  ■  E-mail: [email protected]  ■  801 Avenida Acaso, Camarillo, CA  93012  ■  PO Box 3670, Camarillo, CA  93011

STEP 2:  INSTALL BRACKETS, DEVICE & TRIM

1.   Remove chassis cover from chassis assembly and end cap from end cap bracket.

2.   Cut the length if required.

User information;  This model device has three different lengths:

Approx. 33" = For use on 3' wide door openings.
Approx. 40" = For use on 3.5' wide door openings.
Approx. 44" = For use on 4' wide door openings.

a. The device length are pre-cut for use of 36", 42" and or 48" wide doors, no additional 
    cutting is necessary.  If narrow door installation is required, cut device at section “A” 
    to door width minus 2" for proper fit.
b. Remove device from door, remove end cap and end cap bracket and cut where      
    required.

3.

Mount device horizontally via the drilled holes and secure with supplied
 mounting hardware.  Attach device to trim or sexbolt.

4.

If installing trim verify that the actuator shaft is fully inserted
 into the device cam (Refer to view “B”).

5.

Install end cap bracket to device, level
device and mark before mounting.

6.

Install mounting brackets to top and bottom
of door.

Summary of Contents for S6200 Series









Reviews: