Screen Innovations Solo 3 Installation Instructions Manual Download | Manualshive

Page: 12 / 24

background image

12

7. Reaching under the cassette, move levers up into the locked position, keeping the screen secure.

To finish installation, continue with the steps below.
6. Locating the channel running along the back of the screen, hook the channel onto the wall brackets.

INSTALLATION – SOLO 3 375 EXTERNAL– INDOOR

Installation – Solo 3 375 External – Indoor

channels

«
...
10
11
12
13
14
...
»

Summary of Contents for Solo 3

























Reviews:

No comments

Related manuals for Solo 3

ADVANTAGE ELECTROL

Brand: Da-Lite Pages: 2

Brand: Optoma Pages: 21

Brand: Draper Pages: 2

Brand: IGNIA LIGHT Pages: 16

ECO Spot PCE Series

Brand: Globus New Media Pages: 4

Brand: Optoma Pages: 67

Brand: Panasonic Pages: 111

Brand: Panasonic Pages: 112

Brand: Panasonic Pages: 150

Brand: Panasonic Pages: 212

Brand: Panasonic Pages: 213

Brand: Digital Projection Pages: 80

Brand: AbiS Pages: 12

Brand: Briteq Pages: 31

Brand: EyeClick Pages: 16

Brand: Optoma Pages: 2

Large Cosmopolitan Electrol

Brand: Da-Lite Pages: 12

Multi vision imager

Brand: Da-Lite Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands