Screen Innovations Solo 3 Installation Instructions Manual Download | Manualshive

Page: 19 / 24

background image

19

Servicing – Tube Installation

3. To level Solo 3 375 models, note that the idler bearing is positioned on a spring loaded plate that

moves up and down. To level this model, set the plate to the appropriate position and tighten

using the hole at the bottom of the end cap.

SERVICING SOLO 3 375 – TUBE INSTALLATION

«
...
17
18
19
20
21
...
»

Summary of Contents for Solo 3

























Reviews:

No comments

Related manuals for Solo 3

51MP6100D - 51" Widescreen Hd Ready Tv

Brand: Magnavox Pages: 38

Brand: Screen Technics Pages: 8

Brand: Optoma Pages: 67

Brand: Optoma Pages: 2

Brand: BenQ Pages: 32

Brand: Barco Pages: 7

Brand: Ask Proxima Pages: 32

Brand: Panasonic Pages: 6

PT-LB2U PT-LB1E

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 5

Brand: Panasonic Pages: 6

PT-LB10U - Mobile Projector XGA 2000 Lumens

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 5

Brand: Panasonic Pages: 5

Brand: Panasonic Pages: 6

PT-LB10NTU - Mobile Proj XGA 2000 Lumens 4.9LBS Cross Platform Wrls

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands