background image

 

SCOTTY DA-42 MPP Rack 

5 Setup 

5.1 Setup of the SATCOM Transceiver 

For optimal performance of the INMARSAT Transceiver HSD-400 within the 
SCOTTY solution, the transceiver should be configured once. 

Usually, no configuration is required

 as SCOTTY already configures all 

necessary settings. In case the configuration has been damaged, follow these 
directions. 
 

1.  Start the SCOTTY EMS HSD software and open the Terminal window. 

See chapter 4.1 “EMSHSD SW” for details. 

Alternatively, use a terminal emulation program like HyperTerm with 
19200 Baud, 8N1 

2.  Make sure the serial port of your PC is connected to the HSD-400 
3.  Make sure the HSD-400 is powered up and has finished its initialization 
4.  Enter “maint” (no echo displayed). MENU 1 should be displayed. 

Note: use “Ctrl+N” and “Ctrl+O” to navigate through the menus 
 

5.  Press “Ctrl+N” to switch to MENU 2. 
6.  Press “T” (enter time of day) and enter current date and time.  

Follow the syntax given, e.g. “7/1/2008 9:50:00” 

 

7.  Press “Ctrl+N” to switch to MENU 3. 
8.  Press “M” (misc. eeprom parameters) 
9.  Enter “3” (GPS protection algorithms) and enter “0” (disabled) 
10. Press “M” (misc. eeprom parameters) 
11. Enter “97” (channel card configuration), press “S” two times (swift64) 

Note: This setting forces the transceiver into Swift64 mode required for 
ISDN connections at higher rates. 

12. Press “I” (enter all LES id’s) and enter the ID of your provider, e.g. 

“002” 

Maintenance Manual 

21 

Summary of Contents for DA-42 MPP Rack




































Reviews: