background image

C1448, C1848, C2148 E Series

Remote Condenser Models - User Manual

February 2016

Page 13

Final Check List:

1.  Is the unit located indoors in a controlled 

environment?

2.  Is the condenser located where it can receive 

adequate cooling air?

3.  Has the correct electrical power been supplied to 

the machine?

4.  Have all the water supply connections been 

made?

5.  Have all the drain connections been made?

6.  Has the remote condenser been properly 

installed?

7.  Has the interconnecting tubing been properly 

routed between the remote condenser and the ice 

machine?

8.  Have the quick connects been properly 

connected?

9.  Has the power supply wire from the ice machine 

to the remote condenser been properly run and 

connected?

10. Has the unit been leveled?

11. Have all unpacking materials been removed?

12. Is the water pressure adequate?

13. Have the drain connections been checked for 

leaks?

14. Has the bin interior been wiped clean or sanitized?

15. Have any water filter cartridges been replaced?

16. Have all required kits and adapters been properly 

installed?

Lower Light and Switch Panel

This user accessible panel provides important 

operational information and duplicates the lights and 

switches on the controller. It also allows access to 

the On and Off buttons that operate the ice machine. 

Sometimes access to the switches should be limited 

to prevent unauthorized operation. For that purpose 

a fixed panel is shipped in the hardware package. 

The fixed panel cannot be opened.

To install the fixed panel:

1.  Remove the front panel and remove the bezel.

2.  Spread the bezel frame open and remove 

original door, insert fixed panel into bezel. Be 

sure it is in the closed position. 

3.  Return bezel to panel and install panel on unit.

Open door to access On 

and Off switch buttons.

Summary of Contents for C1448MR-32
























Reviews: