background image

BC0530 User Manual

March 2020

Page 10

◊ 

Is the ice maker and bin assembly level?

◊ 

Is there proper clearance around the machine for air circulation?

◊ 

Have all electrical, water and sewer connections been made?

◊ 

Has the supply voltage been tested with the ice ma+er on a dedicated, protected circuit?

◊ 

Is the machine installed where ambient air temperatures will range from 45 to 90F (7 to 32C)?

◊ 

Is the machine installed where incoming water temperatures will range from 45 to 90F (7 to 32C)?

◊ 

Does the water supply provide a minimum 20 psig dynamic to maximum 100 psig static pressure?

◊ 

Are there separate drain lines for the ice maker and bin?

◊ 

Are the ice makers and bin drains vented?

◊ 

Is the bin thermo probe run correctly, secured, tested and positioned in the bin at the right level?

◊ 

Are the electrical lines free from contact with refrigerant lines and moving parts?

◊ 

Are the drain pan and ice chute positioned properly and is the packing tape removed?

◊ 

Have you cleaned and sanitized the ice maker and bin?

◊ 

Is the mode selector switch set to the ice position?

◊ 

Are the cabinet panels secured?

◊ 

Has the owner been instructed regarding cleaning, maintenance and the manual?

◊ 

Has the owner completed the registration card?

◊ 

Have you left the installation and operation manual?

Installation Check List

Summary of Contents for BC0530


















Reviews: