manualshive.com logo in svg

SciCan STATIM 900J, Operator'S Manual, Page: 29 / 31

Share
Download
SciCan STATIM 900J Operator'S Manual Download Page 29

STATIM

 900J Operator’s Manual

29

1.  Statim 900J 

SJ00R604

2.  Unit # :  

OOO

3.  CYCLE NUMBER 

00006

4.  16:10  

04/12/2007

5.  SOLID INSTRUMENTS
6.  134 C for 3.5 min.
7.  CYCLE START  

0:00

8. CONDITIONING 

1:35

9.  PRESSURIZING  

2:40

10. STERILIZING 

3:14

11.  136.5 C 227kPa  

3:14

12.  135.7 C 220kPa  

3:44

13.  136.4 C 226kP a  

4:14

14.  136.5 C 227kPa  

4:44

15.  135.9 C 221kPa  

5:14

16.  136.4 C 227kPa  

5:44

17.  135.9 C 221kPa  

6:14

18.  136.4 C 226kPa  

6:44

19. VENTING 

6:44

20.  CYCLE COMPLETE   6:59

8. Limited Warranty

For a period of one year, SciCan Ltd. guarantees that the STATIM 900J, when 

manufactured by SciCan Ltd. in new and unused condition, will not fail during 

normal service due to defects in material and workmanship that are not due to 

apparent abuse, misuse, or accident. In the event of failure due to such defects 

during this period of time, the exclusive remedies shall be repair or replacement, 

at SciCan Ltd.’s option and without charge, of any defected part(s) (except 

gasket and filters), provided SciCan Ltd. is notified in writing within thirty(30) 

days of the date of such a failure and further provided that the defective part(s) 

are returned to SciCan Ltd. prepaid.
This warranty shall be considered to be validated, if the product is accompanied 

by the original purchase invoice from the authorized SciCan Ltd. dealer, and 

such invoice identifies the item by serial number and clearly states the date of 

purchase. No other validation is acceptable. After one year, all SciCan Ltd.’s 

warranties and other duties with respect to the quality of the product shall 

be conclusively presumed to have been satisfied, all liability therefore shall 

terminate, and no action or breach of any such warranty or duty may thereafter 

be commenced against SciCan Ltd.
Any express warranty not provided hereon and any implied warranty or 

representation as to performance, and any remedy for breach of contract which, 

but for this provision might arise by implication, operation of law, custom of 

trade or course of dealing, including any implied warranty of merchantability 

or of fitness for particular purpose with respect to all and any products 

manufactured by SciCan Ltd. is excluded and disclaimed by SciCan Ltd. If 

you would like to learn more about SciCan Ltd. products and features, visit our 

website at www.scican.com.

Summary of Contents for STATIM 900J
































Reviews:

No comments