background image

GP-M40J-CX-08A 

4001/2-J, 4N11/2-J Manual 

    RD: April 2006 

R.L. 08A 

KH 

8.3  SAFETY        

 

Check periodically for leaks in the system, or immediately when you smell gas. 

In case a leak is detected, extinguish all open flames in the area. 

Never leak test while smoking. 

If you cannot repair a leak, turn off gas supply at the cylinder valve and contact your gas supplier 

      or a qualified, licensed gas technician. 

Do not alter or modify this heater in any way 

 
 

 

8.1 STORAGE 

 
 

When heater is not in use for a prolonged period of time, remove gas cylinder. 
 
Verify that the gas valve is fully and tightly closed. 
 
Do not store the gas cylinder indoors. 
 
Store gas cylinder in a well ventilated area. 
 
For more compact storage and to avoid damage, the reflector may be removed 

8.2 PREVENTATIVE CARE AND MAINTENANCE 

 

The burner area is likely to attract spiders, especially inside orifices. Once a year, the heater should be 
inspected for spider webs, insects, and debris around burners and orifices. Plugged injectors or orifices 
will obstruct the gas flow to the burner. This will result in burner malfunction or possible damage. 
 
 

Have heater inspected

 

if.….. 

you smell gas combined with yellow tipped flames on burner. 

heater does not provide expected heat capacity 

burner makes little popping sounds while operating, other than when shutting down after  

      being turned off. When heater is warming up or cooling down a pinging metallic noise is normal. 

Page 15 

Summary of Contents for 4001-J SERIES


















Reviews: