background image

 

 

 

Change the door alarm parts with invisible hinge 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Door  

 Lock  

 D

oor alarm magnet   ④

 M

agnet fix hole   ⑤

 Lock fix hole 

 

1. After changing the door, 

first unscrew②

 

lock and ③magn

et like pic1

 

2. Then fix the②lock to the position of ⑤

 lock fix hole 

3. After change the 

 

magnet to position of ④

 magnet fix hole  

 

 

Installation specifications for built-in purposes. 

When unit is being ‘recessed’ into a wall cavity please allow min clearance of 40mm each side and 150mm 

at rear. Units vent through front but space is needed at rewar to allow hot air to escape, space is needed at 

sides as door ‘opens’ outside it’s diameter. 

 

 

Unpacking and cleaning the cooler 

 

Remove the exterior and interior packing materials. 

 

Let the appliance stand upright for approximately 2 hours before connecting it to the power source, 

which helps to reduce the possibility of a cooling-system malfunction from handling during 

transportation. 

Use a soft cloth to clean the interior surface with lukewarm water. 

 

Install the door handle provided with the appliance by following these steps: 

Step 1

 

Remove the gasket at the inner side of the door 

 

to expose the two screw holes, pinching as close as possible to frame to lift out slowly 

Step 2

 

Install the handle tightly with the screws  

and washers provided. 

Step 

Tidy and restore the gasket. 

 

Storage inside the cabinet 

-It is not recommended to store blood or special pharmaceuticals in the fridge, it is not a medical fridge. 

-Keep drinks at least 1cm away from walls to allow air flow and to stop bottles freezing on back wall close 

to ‘cold-plate’. 

 

Summary of Contents for BD425B









Reviews: