schmersal SEP 01.0 Operating Instructions Manual Download Page 13

Page: 13 / 38

SEPK 02.0 / SEPG 05.3 / SEP 01.0 /

SEP 01.4 / SEPLC 05.2 / SEP 07.0 / SEP 09.0

Operating instructions

Two-hand control panel

5.3 Mounting instructions for ADP... type control elements (orde-

ring sufix E1 or E2) and ADRR40 type emergency stop command

devices

General:

• The ADP... type pushbuttons are by default suitable for mounting up to

a wall thickness of max. 4 mm (increased wall thickness possible with

modiied thread ring). The maximum tightening torque for the device

head to tighten the thread ring with an A-14 tool is 1 Nm.

• The supplied EDT-12 double-sided adhesive gasket must be adhered

under the device head prior to the disassembly of the device (to adjust

and secure the pushbutton). The protective ilms of the gasket must

be previously removed.

Fig. 1: a) Front plate

Fig. 2

Fig. 3

Fig. 4: a) Securing plate

5.4 Mounting instructions for EDRR EFR and KDRR EFR type

emergency stop command devices

• Fit the EDR EFR emergency stop actuator in non-actuated condition

by means of the ELM mounting lange, align and tighten (max. 0.6

Nm).

• Snap the EFR spring element in the middle position of the EFM

mounting lange (position 3). The EFR spring element is supplied in

tensioned condition.

• The EDR EFR actuator is latched, i.e. mechanically ixed, to the EFR

spring element by actuation. By rotating to the right and consecutive

pulling, the spring element is retensioned and the emergency stop

command device is brought back to its basic position.

• Snap the EF contact element(s) into position(s) 1 (and/or 2) of the

EFM mounting lange.

• EFR spring element: to avoid itting errors, we recommend to it the

enclosed locking plate (A) by means of both locking rings (B) 4 mbo

09 after the contacts have been snapped on (see photo). No special

tools are required. This locking plate ensure a proper itting and ixati-

on of the contact elements.

Fig. 5

• The emergency stop device is now ready for operation.

5.5 Mounting instructions for EDR type emergency stop command

devices

• Fit the EDRZ emergency stop actuator in non-actuated condition by

means of the EFM mounting lange, align and tighten (max. 0.6 Nm).

Do not actuate the emergency stop actuator!

• Snap the EF contact element(s) into position(s) 1 (and/or 2 and 3) of

the EFM mounting lange.

• The emergency stop device is now ready for operation.

5.6 Mounting instructions for BWT sensor button

In constructions for the assembly and putting into operation of

BWT-1/BWT-2, the requirements of EN 574 must be impera-

tively observed!

Deinition of "two-hand control panel"

A two-hand control panel requires a simultaneous actuation with both

hands to start and maintain the operation of a machine, as long as

there are risks. A two-hand control panel must be located outside the

hazardous area, to prevent the operator from entering this area before

the machine has come to a complete standstill.

Summary of Contents for SEP 01.0







































Search results

Summary of Contents for SEP 01.0

Reviews:

Related manuals for SEP 01.0

Brands by name

Popular brands

schmersal SEP 01.0, Operating Instructions Manual

Search results

Summary of Contents for SEP 01.0

Reviews:

Related manuals for SEP 01.0

Brands by name

Popular brands