Schmeiser HBT2N Operation And Parts Manual Download Page 10

Bin Trailer

T. G. Schmeiser Co., Inc.

Ph. (559) 268-8128

Fax (559) 268-3279

www.tgschmeiser.com

10

Tractor Requirements

OPERATION SAFETY

WARNING

Crush Hazard (Rolling Over)

Do not clean, lubricate, or make adjustments

while the unit is moving .

Never allow inexperienced or untrained
personnel to operate the implement or tractor

without  supervision .

Enter And Exit Tractor

To avoid being run over, do not enter or exit
tractor when it is moving .  Avoid serious injury or
death, from contact with rotating tires, by

entering or exiting tractor only when it is completely
stopped .

Safe Distance

Keep all bystanders, especially children, away
from the tractor and implement during operation .

Overturn Hazard

Pick the most level route possible when
transporting across fields.  Avoid the edges of

ditches, gullies, or steep hillsides .
Be especially careful when turning on slopes with the
wheels down .  Never turn uphill with the wheels down
except at slow speed and a low rate of turn .
Never transport or operate this machine on steep slopes

Periodically clear the unit of brush, twigs, or other
materials to prevent buildup of dry, combustible
materials .

Visually check all fasteners for tightness
or damage before and after operation .
Repair immediately if required .

SAFETY INSTRUCTIONS

Tractor Owner/Operator Manual

Always refer to the tractor Operator’s Manual
to ensure compatibility and maximum safety .

Be familiar with the location, settings, and function of the
tractor controls before using this equipment .

WARNING

SAFETY INSTRUCTIONS

Do not use a tractor of more than the recommended HP
to prevent damaging implement components.

If transporting or operating the tractor and implement
near a public roadway, the tractor must be equipped
with proper warning lighting and a Slow Moving Vehicle
(SMV) emblem, which are clearly visible from the rear of
the unit.  Lights and a SMV emblem must be attached
directly to the implement if the visibility of the tractor
warning signals is obscured.

Never operate the tractor PTO with the PTO master
shield missing or in the raised position.

Rollover Hazard

To avoid serious injury or death from
falling off tractor, equipment runover,

rollover, or crushing:
1)  Use ROPS equipped tractor .
2)  Keep ROPS locked in the UP position .
3)  Only operate the equipment when seated in the

tractor seat .

4)  Always fasten seat belt when operating the tractor

and Implement .

ROPS and Seat Belt

Tractor Safety Devices

The tractor must be equipped with a Roll Over Protective
Structure (ROPS) (tractor cab or roll-bar) and seat belt to
protect the operator from falling off the tractor, especially
during a roll-over where the driver could be crushed and
killed.
Only operate the tractor with the ROPS in the raised
position and seat belt fastened.

WARNING

Summary of Contents for HBT2N





























Reviews: