manualshive.com logo in svg

Schmalz FMHD Series, Operating Instructions Manual

Share
Download
Schmalz FMHD Series Operating Instructions Manual Download Page 49

 

30.30.01.01648/03 

www.schmalz.com 

EN   | 49 

11 Pneumatic Circuit Diagram 

 Pneumatic Circuit Diagram FMHD 

11.1

 

FMHD with separating cylinder and blow-off function 

 

Optimum flowing compressed air pressure 6.0 bar 

 
 
 
 
 

 
Before initiating the blow-off pulse, ensure that the gripper (with attached workpiece) is not pressed 
against a solid surface. The workpiece must be able to freely detach from the gripper. 
 

 

 

 

Maximum overpressure 

The maximum overpressure in the gripper (vacuum reservoir or valve chamber) 
must be limited to a maximum of 0.2 bar. For example, no continuous blow-off pulse 
as long as the gripper is placed on a workpiece in the waiting position, or similar. 

 
 
 
 
 
 

 

2 

1 

“Blow off ON/OFF” 
control valve 

“Cylinder ON/OFF” 
control valve 

Function integrated in the 
end cover  
  

Area gripper 

Check valve displayed 

Cylinder 

Vacuum generator  
provided by customer 

 

 

Provided by customer (flow pressure 6.0bar) 

Summary of Contents for FMHD Series





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands