Schiller BOB-CAT QUICKCAT 912480 Operator'S Manual Download Page 4

Page: 4 / 34

QUICKCAT

MOWERS

SAFETY

NOTICE !!!

Unauthorized modifications may present

extreme

safety hazards to operators and bystanders and

could also result in product damage.

Schiller Grounds Care, Inc. strongly warns against,

rejects and disclaims any modifications, add-on

accessories or product alterations that are not

designed, developed, tested and approved by Schiller

Grounds Care, Inc. Engineering Department. Any

Schiller Grounds Care, Inc. product that is altered,

modified or changed in any manner not specifically

authorized after original manufacture–including the

addition of “after-market” accessories or component

parts not specifically approved by Schiller Grounds

Care, Inc.–will result in the Schiller Grounds Care,

Inc. Warranty being voided.

Any and all liability for personal injury and/or property

damage caused by any unauthorized modifications,

add-on accessories or products not approved by

Schiller Grounds Care, Inc. will be considered

the responsibility of the individual(s) or company

designing and/or making such changes. Schiller

Grounds Care, Inc. will vigorously pursue full

indemnification and costs from any party responsible

for such unauthorized post-manufacture modifications

and/or accessories should personal injury and/or

property damage result.

MODEL NUMBER:

This number appears on sales

literature, technical manuals and price lists.

SERIAL NUMBER:

This number appears only on

your mower. It contains the model number fol-

lowed consecutively by the serial number. Use this

number when ordering parts or seeking warranty

information. Located behind rider pad on frame of

unit.

This symbol means:

ATTENTION!

BECOME ALERT!

Your safety and the safety of others is involved.

Signal word definitions

The signal words below are used to identify levels

of hazard seriousness. These words appear in this

manual and on the safety labels attached to Schiller

Grounds Care, Inc. machines. For your safety and

the safety of others, read and follow the information

given with these signal words and/or the symbol

shown above.

DANGER

indicates an imminently hazardous

situation which, if not avoided,

WILL

result in death

or serious injury.

WARNING

indicates a potentially hazardous

situation which, if not avoided,

COULD

result in

death or serious injury.

CAUTION

indicates a potentially hazardous situation

which, if not avoided,

MAY

result in minor or moderate

injury. It may also be used to alert against unsafe

practices or property damage.

CAUTION

used without the safety alert symbol

indicates a potentially hazardous situation which, if

not avoided,

MAY

result in property damage

Summary of Contents for BOB-CAT QUICKCAT 912480



































Search results

Summary of Contents for BOB-CAT QUICKCAT 912480

Reviews:

Related manuals for BOB-CAT QUICKCAT 912480

Brands by name

Popular brands

Schiller BOB-CAT QUICKCAT 912480, Operator'S Manual

Search results

Summary of Contents for BOB-CAT QUICKCAT 912480

Reviews:

Related manuals for BOB-CAT QUICKCAT 912480

Brands by name

Popular brands