Scheppach 7323 0901, Translation From The Original Instruction Manual

Page: 14 / 109

english 15
Regularly check the electrical connection lines for dam -
ages. Please make sure that the connection lines are dis-
connected from the mains supply during the check.
Electrical connection lines must comply with the relevant
VDE and DIN regulations. Only use connection lines la -
belled with H 07 RN. The labelling of the connection cable
with the type specification is required.
AC motor Fig. 11
• The supply voltage must be 230 V / 50 Hz.
• Extension lines up to a length of 25 m must have a cross
section of 1.5 square millimetres. Extension lines with a
length of more than 25 m must have a minimum cross
section of 2.5 square millimetres.
• The mains connection is protected with a delay-action
fuse of 16 A.
Rotary current motor, Fig. 12
• The power supply must be 400 Volt/50 Hz.
• The electrical connection and extension cords must have
five wires = 3P + N + SL.
• Extension cords up to 25 metres in length must have a
cross section of 1.5 square millimetres; those over 25
metres must have a cross section of at least 2.5 square
millimetres.
• The electrical connection is secured with a 16 A fuse.
• Before the first connection, or when the site is changed,
the direction of rotation should be checked and, if nec-
essary, the polarities switched round.
If you have further questions, please specify the follow-
ing:
• Motor manufacturer
• Kind of current of the motor
• Data from the machine type plate
• Data from the switch type plate
If you return the motor, always return the complete drive
unit with the switch.
Maintenance
Perform resetting, measuring, and cleaning work exclusive-
ly when the motor is turned off. Disconnect the mains plug,
and wait until the rotating tool stands still.
All protection and safety devices must be immediately re-
installed once the repair and maintenance work is com-
pleted.
The built-in ball bearings are maintenance-free.
Recommendations:
• Slightly re-lubricate the slewing segments of the table
and the bend tensioning device.
• Regularly clean the saw band. Wood leaves resin sedi -
ments. We recommend the deresinifying concentrate
Pharmol HEK, item no. 61009700 for the cleaning.
• Regularly check the guiding rollers and the counterpres -
sure bearings. If required, readjust or disassemble them,
and grease or exchange the parts.
• Exchange worn-out table inserts.
• Ensure that the tabletop is always free of resin.
Special Accessories
Article/
Application
Width Size Length Tooth/Inch Art. No.
saw band/
standard
12 0,65 2895 4 7323 0701
saw band/
curving, sweep&
fret cut
6 0,65 2895 6 7323 070 2
saw band/
for non-ferrous
metals
6 0,65 2895 10 7323 070
3
saw band/
cut on edge, upright
15 0,65 2895 4 7323 070 4
saw band/
fine-cut
12 0,65 2895 10 7323 070
5
saw band/
wood and metal
20 0,60 2895 4 7323 070
7
saw band/
cut on edge, upright
30 0,60 2895 4 7323 070
8
saw band/
for non-ferrous
metals
6 0,65 2895 24 7323 070
9
EC Declaration of Conformity
We, Scheppach Fabrikation von Holzbearbeitungsmaschinen GmbH,
Günzburger Str. 69, D-89335 Ichenhausen
hereby declare that the ma-
chine named below correspondends to the relevant safety and health
requirements of the EC guidelines specified below in its design and
construction and in the version which we introduced to the market.
This declaration becomes invalid if changes are made to the machine
without our consent.
Machine description:
Band saw
Machine model:
Basato 4
Relevant EC directives:
EC machine directive 98/37/EG (< 28.12.2009), EC machine directive
2006/42/EG (> 29.12.2009), EC Low voltage directive 2006/95/EWG,
EC-EMV directive 2004/108/EWG.
Applied harmonized European Standards:
EN292-1, EN292-2, EN294, EN349, EN418, EN847-1, EN954-1, EN1088,
EN50082-1, EN60204-1, EN101014, EN60555-2, EN60555-3, EN61029-
1, EN61029-2-5
Applied national technical standards and specifications, especially:
ISO 7960
Notified body within the meaning of Annex VII
Prüf- und Zertifizierungsstelle
Fachausschuss Holz
Vollmoellerstraße 11
70563 Stuttgart-Vaihingen
Engaged for
EG-Baumusterbescheinigung, Staub prüfung
Date
Ichenhausen, 01.03.2007
Signature:
on behalf of Wolfgang Windrich
(Technical manager)