www.scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
Noise
Sound values were measured in accordance with
EN 61029.
Sound pressure level L
pA
70,7 dB(A)
Uncertainty K
pA
3 dB
Sound power level L
WA
86 dB(A)
Uncertainty K
WA
3 dB
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Limit the noise to a minimum!
•
Only use appliances which are in perfect working
order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever necessary.
•
Switch the appliance off when it is not in use.
7. Before operation
WARNING:
For your own safety never connect plug to power source
outlet until all assembly steps are completed and you
have read and understood the safety and operational in-
structions
Column to base, Fig. 3
Position base {1) on floor or bench.
Place column assembly {2) on base and align holes in
column support with holes in base.
To attach and fasten the pillar unit, screw the three
screws (a) into the base plate and tighten them with a
wrench.
Table and pillar, Fig. 4
Slide the drilling table (3) onto the pillar (2). Position the
table directly above the base plate.
Install the table bolting (b) in the table unit from the left
side and tighten it.
Machine head and pillar, Fig. 5
Place the machine head (4) onto the pillar (2).
Put the spindle of the drilling machine with the table and
the base plate in the cover and fasten the 2 Allen screws
(c).
Drill chuck protection with depth stop, Fig. 6
Fit the chuck protection with depth stop (8) onto the spin-
dle pipe and tighten the slotted screw (d).
Caution! The depth stop must be fed through the drilling
(13) on the housing. Screw on the two nuts (B1/2) and
place the indicator (g) onto the depth stop. The indicator
(g) must point at the scale.
Feed handles to the shaft hub, Fig. 7
Screw the feed handles (A) tightly into the threaded
holes in the hub (B).
Remaining hazards
The machine has been built using modern technolo-
gy in accordance with recognized safety rules. Some
remaining hazards, however, may still exist.
• Long hair and loose clothing can be hazardous when
the work piece is rotating. Wear personal protective
gear such as a hair net and tight fitting work cothes.
• Wood chips and saw dust can be health hazard. Be
sure to wear personal protective gear such as safe-
ty goggles and a dust mask. Use a vacuum exhaust
system.
• Thrown work pieces can lead to injury if the work piece
is not properly secured or fed, such as working with-
out a limit stop.
• The use of incorrect or damaged mains cables can
lead to injuries caused by electricity.
• Even when all safety measures are taken, some re-
maining hazards which are not yet evident may still
be present.
• Remaining hazards can be minimised by following the
instructions in „safety precautions“, „proper use“ and
in the entire operating manual.
Keep this safety information in a safe place.
6. Technical data
Dimensions L x B x H mm
430x200x580
Chuck size mm
13
Spindle cone seat
B16
Drilling chuck cone seat
B16
Drilling chuck clamping range mm
1,5 - 13
Spindle rise and fall range mm
50
Chuck to worktable mm
138
Spindle base working range mm
215
ø Column mm
46
Weightt kg
14,4
Drive
Rated voltage V/Hz
230/50
Power rating
350W S2
15min
Speeds 1/min
600 / 900 /
1450 /
1950 / 2600
Subject to technical modifications!
Load factor:
A load factor of S2 15 min (intermittent periodic duty)
means that you may operate the motor continuously at
its nominal power level (350 W) for no longer than 15
minutes ON period. If you fail to observe this time limit
the motor will overheat. During the OFF period the mo-
tor will cool again to its starting temperature.
22 / 52
GB
