background image

 

23 

7. WARRANTY 

 
The  equipment  and  the  relevant  accessories  are  guaranteed  12  months  from  delivery.  The 
guarantee  does  not  include  consumable  items  (filters,  carbon  filters,  membranes,  etc.).  The 
“ERS”  pressure  amplification  device  is  guaranteed  36  months,  provided  that  the  annual 
maintenance is performed at a Schenker service point. 
The  guarantee  covers  faults,  defect  of  materials  and  parts.  It  is  limited  to  the  replacement  or 
repair  of  faulty  parts.  The  expense  for  the  disconnecting  and  reinstalling  on  the  vessel  and 
transport of the equipment from or to our Service Point, or our factory will be at the customers 
own expense. 
The under guarantee delivered parts transport, will be at customer’s own risk. 
In  case  of  repairs  under  guarantee  performed  by  our  technicians  on  the  customer  vessel,  the 
faulty parts replacement cost will be at Schenker's expense, while manpower and travel expenses 
will be charged  to the customer. The guarantee does not include faults caused by negligence in 
operating,  maintenance  and  installation  of  the  device  (if  not  carried  out  by  an  authorised 
Schenker Service point). 
Dismantling by non-authorized personnel will render void all guarantees. Schenker Italia can not 
be held liable for any direct or indirect damage caused by the malfunctioning equipment, limiting 
its responsibility to the repair and replacement of faulty parts.

 

 
 
 
 
 

Summary of Contents for READY Electron 60
























Reviews: