background image

 

2. Installation 
2.1 General criteria  

A planned installation will make both fitting and operation of your Ready 60 watermaker easier. 
Details below need to be taken into account with your installation: 
 

 

An appropriate seawater intake with necessary fittings. 

 

Positioning of the watermaker . 

 

Positioning of accessories. 

 

Pipework and cable laying. 

A good installation needs to be easy to use, easy to access for maintenance and filter changes. All 
Watermaker components have been designed to achieve all of this. Draw a schematic electric and 
hydraulic connection diagram when the installation plan is complete and keep it with this manual 
for reference.  

 

2. Installation 
2.2 Components mounting 
 

Watermaker positioning.  
The  horizontal  and  vertical  distance  of  the  watermaker,    from  the  sea  water  inlet,    is  a  critical 
aspect of the installation. Even if the pumps are self-priming type,  it is strictly adviced to install 
the watermaker   as low as possible respect the sea level, and as close as possible respect the 
sea  water intake.  
If  the  watermaker  is  positioned  too  much  above  respect  the  sea  level  or  too  far  from  the  water 
inlet,  the pumps will have difficult in inhaling water and frequent blocks can occur.  
Usually  the  vertical  distance  respect  the  sea  level  is  more  critical  than  the  horizontal  distance 
from the water intake. In example if the unit is positioned below the sea line, a distance from the 
water inlet up to 3 meters can be tolerated. 
On contrary, if the watermaker is positioned above the sea level,  it is recommended a distance 
from the water inlet of max 1-2 mts. 
Anyway never  install the unit above more than 30 cm. respect  the sea level. 
 
Avoid locating the unit where a loss of water can cause damage or jeopardize its safety.  
Allow sufficient space for access to the casing containing the filter cartridge. 
The unit must be installed horizontally on a suitable base strong enough to support its weight. 
 It may be necessary to create a suitable wooden or fiberglass structure for the unit if an existing 
one not available. Avoid installing it on a surface susceptible to vibration.  
The unit can be a little noisy in operation. Possible areas for siting are: sink closets, under berth 
lockers, wardrobe bases (creating a false floor above it.)   
 
Active carbons filter 
The active carbons filter (and the preassembled electro-valve)  need to be positioned vertically. 
There are not specific restriction regarding the distance from the watermaker. The filter housing 
is  fixed,  by  means  of  Parker  type  screws,  through  the  bracket  supplied. It is necessary to leave 
sufficient space below to allow unscrewing replacement of the filter. 

 
 
 
 
 
 
 

Summary of Contents for READY Electron 60
























Reviews: