3
1
2
Line Scan Camera SK6288GKOC-L Manual (06.2015) • shar
ed_Installation-ElectrV_ML.indd (06.2015)
8
2 Installation and Setup
SK6288GKOC-L
Instruction Manual
(06.2015)
© 2015
Schäfter + Kirchhoff GmbH
•
Hamburg
2.2 Electrical Installation: Connections and I/O Signals
External Synchronization Cable SK9024.x
Use this cable to feed external synchronization
signals into socket
2
.
Connectors:
Hirose plug HR10A, female 12 pin (camera side)
Phoenix 6 pin connector incl. terminal block (for
synchronization signals)
Length 3 m or 5 m. Other lengths on request.
Power Cable SK9015.x
Use this cable to feed external supply voltage into socket
1
.
Connectors:
Hirose plug HR10A, female 6 pin (camera side)
Lumberg SV60, male 6-pin connector (for supply voltage)
Length 1.5 m (standard) or 0.2 m
Network Cable CAT6.x
For connecting socket
3
with the PC Ethernet
interface. Both ends with RJ45 connectors.
Power Supply Unit PS051515
Input: 100-240 VAC, 0.8 A, 50/60 Hz, IEC 320 C14 coupler
(for IEC C13 power cord)
Output: +5V DC, 2.5 A / +15 V DC, 0.5 A / -15 V DC, 0.3 A
Cable length 1 m, with Lumberg connector KV60,
female 6-pin
(for power cable SK9015.x or SK9016.x)
•
For the SK6288GKOC-L line scan camera data transfer and camera control is
provded by the Gigabit Ethernet interface
3
. Use a CAT6 twisted-pair cable to
connect the camera with a PC. The maximum cable length is 100 m.
• The operating power has to be supplied by an external source into socket
1
•
If you want to operate the camera in FREE RUN trigger mode, the connection is
completed with the CAT6 Ethernet cable and the connection to an external power supply.
• For any kind of synchronized operation the external trigger signal(s) have to be wired to socket
2
in addition.
A frame synchronization signal and two separate line synchronization signals can be handled. The various
trigger modes are particularly described in section
Synchronization of the Imaging Procedure and the Object
Scan Velocity, p. 19
1
Power +5V, +15V
Hirose series 10A, male 6-pin
Pin
Signal
Pin
Signal
1
+15 V
4
+5 V
2
+15 V
5
GND
3
+5 V
6
GND
2
1
3
4
5
6
7
8
9
10
11
12
2
1
3
4
5
6
2
1
3
4
5
6
7
8
9
10
11
12
2
1
3
4
5
6
Pin
Signal
1
GND
8
FrameSync IN
10
LineSync A IN
6
LineSync B IN
2
I/O Connector
Hirose series 10A, male 12-pin
TTL_Inx Specification
Max. input frequency
16.5 Mhz
Input voltage,
absolute max. range
min -0.5 V
max 7.0 V
Input voltage max. low
0.99 V
Input voltage min. high
2.31 V
Input current
10 µA
2 Installation and Setup
3
Data
RJ45 con nector for Gigabit Ethernet cable
Status indicators
Network connection speed
Network activity
off
no connection,
10 Mbyte/s connection, or
100 Mbyte/s connection
on
1 Gbyte/s connection
off
no connection
on
connected
flash
light
data is being
transmitted or
received
Accessories
(see also
Accessories and Spare Parts, p. 28)
:
Carry out the
software installation
prior to connecting
the network cable.
(see section 2.3 )
!
