Scarlett SC-054, Instruction Manual

Page: 4 / 18

IM011
www.scarlett.ru SC-054/SC-055/SC-1168/SC-1169 4
GB INSTRUCTION MANUAL
IMPORTANT SAFEGUARDS

Please read all the instruction manual before use and save it for future references.

Before first switching on check that the voltage indicated on the rating label corresponds with the mains voltage in your
home.

For home use only. Do not use for industrial purposes. Use the appliance only for its intended use.

Do not use outdoors or in damp area.

To prevent risk of electric shock and fire, do not immerse the appliance in water or any other liquids. If it has happened
DO NOT TOUCH the appliance, unplug it immediately and check in a service center.

Do not use the appliance in immediate proximity to
а bath, а shower or а swimming pool.

Never pull the cord while disconnecting from the power outlet; instead, grasp the plug only and pull to disconnect.

Do not allow the cord to touch sharp edges and hot surfaces.

Always unplug the appliance from the power supply when not in use.

If the power cord is damaged it should be replaced by the manufacturer or authorized servicing center or qualified
professional for safety reasons.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning
use of the appliances by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

Do not leave appliance unattended while operating.

The appliance must be used only in the upright position.

Unit surface temperature of the appliance is high, thus do not touch it, except the handle.
CAUTION:

To avoid a circuit overload, do not operate another high wattage appliance on the same circuit.

Do not cover the appliance when in use.

The heater is filled with a certain quantity of special oil. Any maintenance that requires opening of the oil tank may be
performed only by the manufacturer or its authorized service center that should repair the appliance in case of oil
leakage.

It is necessary to follow the instructions concerning used oil utilization.

If the product has been exposed to temperatures below 0ºC for some time it should be kept at room temperature for at
least 2 hours before turning it on.

The manufacturer reserves the right to introduce minor changes into the product design without prior notice, unless
such changes influence significantly the product safety, performance, and functions.
WHEELS MOUNTING (FIG. A)

First turn the unit upside-down.

Install multidirectional rolling wheels to each end between the first and the second groups of the heating flanges.

Let the “U” shape screw surround the dome of the heating flanges. Then insert it into two holes of the supporting plate.

Use butterfly nuts to screw them tightly counterclockwise.

Brackets and nuts are supplied with the appliance.

Place heater normally and make sure that it is inconvertible.
USING THE APPLIANCE

Set the power regulator in "0" position and set the temperature reg
ulator in “MIN” position. Connect the appliance to
the mains.
POWER SELECTOR

You can adjust oil heater current power using power regulator:
–
“0” – Off;
–
“I“ – Minimum power;
–
“II” – Medium power;
–
“III” – Maximum power.

During operation, the corresponding power LED will light.
THERMOREGULATOR

Set thermoregulator
to maximum position“MAX”.

When the temperature rises to satisfying level, slowly turn the thermostat counterclockwise until the indicator lights is
out, and the room temperature thus can keep constant.

If you want to change the room temperature, you can make another regulation: turn the thermostat clockwise to arise
the temperature and counterclockwise to lower it.
NOTES:

The room must be properly sealed, if not, using of oil heater will not make good result because of heat
leakage.

After use, turn the power selector to the “0” position, then turn the thermoregulator to the minimal position and unplug
from power supply.
CLEAN AND CARE

The oil heater should be cleaned regularly to wipe out the dust on the surface of fins. As this may result the radiating
efficient.

Unplug from the power supply and allow the appliance to cool down.