Scanjet SC 40RT Instruction Manual Download Page 34

Page: 34 / 44

#SC 40RT 06 – 101027

Page 34 of 44

Spare Part List SC 40RT

Pos.

Part No.

Qty.

Description

111a

30316-38

(1)

Turbine Sleeve

Acc. to order

111b

30319-37

(1)

Flow Washer

Acc. to order

112

104737

Screw

113

30219

Top Nut

114

802115

Washer

117

109275

O-ring

119

104758

Screw

120

30270

Cofferdam Plug

121

105095

Screw

122

105926

Nut

123

106148

Washer

124

120266

Pin Bolt

125

109285

O-ring

126

802131-xxx

Main Pipe with Flange

Acc. to order

127

104430

Screw

128

802127

Bearing Lower

129

106576

Splitpin

130

70037

Thrust Bearing

131

70036

Teflon Bearing

133

30111-xx

Inlet Housing

Acc. to order

134

70066

Strainer

135

70098

Expansion Ring

136

20005-x

Adjusting Sleeve Assembly

Acc. to order

137

109263

O-ring

138

20026

Nut

139

20025

Cup

143

802121-25

Nozzle Housing (2 Nozzles)

802141-25

(1)

Nozzle Housing (4 Nozzles)

Optional

145

70011

2 (4)

Nut

146

50158

4 (8)

Flow Guide

147

50156-100-L

2 (4)

Nozzle Tube (Ø6-11 mm)

50156-150-L

2 (4)

Nozzle Tube (Ø12-16 mm)

148

105087

2 (4)

Bolt

149

50155-xx

2 (4)

Nozzle (“-xx” is outlet diameter)

Summary of Contents for SC 40RT













































Search results

Summary of Contents for SC 40RT

Reviews:

Related manuals for SC 40RT

Brands by name

Popular brands

Scanjet SC 40RT, Instruction Manual

Search results

Summary of Contents for SC 40RT

Reviews:

Related manuals for SC 40RT

Brands by name

Popular brands