background image

 

iv

ZOC33

Section 1: Introduction

 

iv

ZOC33

Preface

  

PREFACE

Warnings, Cautions and Notes

The WARNING! symbol indicates that danger of injury for persons and the environment and/or 

considerable damage (mortal danger, danger of injury) will occur if the respective safety precau

-

tions are not taken.

The CAUTION ! symbol indicate danger for the system and material if the respective safety precau

-

tions are not taken.

The ESD note symbol indicates that proper precautions for handling Electrostatic Sensitive Devices 

needs to be taken when performing the related operation.  This includes the use of grounded work 

surfaces and personal wrist straps to prevent damage to sensitive electronic components.

Warranty

 

Scanivalve Corporation, Liberty Lake, Washing

-

ton, hereafter referred to as Seller, warrants to the Buyer 

and the first end user that its products will be free from 

defects in workmanship and materi al for a period of twelve 

(12) months from date of delivery.  Written notice of any 

claimed defect must be received by Seller within thirty 

(30) days after such defect is first discovered.  The claimed 

defective product must be returned by prepaid transporta

-

tion to Seller within ninety (90) days after the defect is first 

discovered.  Seller’s obligations under this Warranty are 

limited to repairing or replacing, at its option, any product 

or component part there of that is proven to be other than 

as herein warranted.

    

Surface transportation charges covering any 

repaired or replace ment product or component part shall 

be at Seller’s expense; however, inspection, testing and 

return transportation charges covering any product or com

-

ponent part returned and redelivered, which proves 

not to be defective, shall be at the expense of Buyer or the 

end user, whichever has returned such product or compo-

nent part.

 

This Warranty does not extend to any Seller product 

or component part thereof which has been subjected to 

misuse, accident or improper installation, maintenance or 

application; or to any product or component part thereof 

which has been repaired or altered outside of Seller’s facili

-

ties unless authorized in writi ng by Seller, or unless such 

installation, repair or alteration is performed by Seller; or 

to any labor charges whatsoever, whether for removal and/

or reinstallation of the defective pro duct or component 

part or otherwise, except for Seller’s labor charges for 

repair or replacement in accordance with the Warran ty.  

Any repaired or replacement product or component part 

there of provided by Seller under this Warranty shall, upon 

redelivery to Buyer, be warranted for the unexpired portion 

of the original product warranty.

     THIS WARRANTY IS IN LIEU OF AND EXCLUDES ALL 

OTHER WARRANTIES, EXPRESS OR IMPLIED, ARISING BY 

Summary of Contents for ZOC 33/64Px




























Reviews: