Scandomestic SKF 618BS, User Manual

Page: 16 / 39

16
The figure above is schematic for installation only, not represent-
ing the actual product. The specific dimension shall be subject to
the product that you have bought.
To ensure proper air circulation around the fridge, please main-
tain sufficient space.If install the top panel or closet, please
maintain sufficient space to move when necessary.
Transport
• Do not carry the refrigerator horizontally or reversely.
• Do not carry the refrigerator by holding the door or handle;
the refrigerator shall be carried by lifting the bottom.
• The refrigerator must be placed on a hard, flat ground; if
cushioning is needed, stable, hard, non flammable cushion
blocks shall be used, rather than the foam backing of refrig-
erator.
• The refrigerator shall be kept away from damp locations
where water is easy to splash; water or dirt shall be removed
with soft cloth timely to prevent rusting which may have an
effect on the electrical Characteristics.
• Place the refrigerator in a well-ventilated place, reserve a
certain space around and behind the refrigerator, and do not
cover or block the air grille on the rear cover plate of com-
pressor at the back of refrigerator; Keep the refrigerator
away from heat source or direct Sunlight.
• When the refrigerator stays in the packing box, plastic feet
are in tightened state. After carrying it out from the packing
box for placement, please make sure to adjust two front
plastic feet until the height is suitable; just adjust two plastic
feet with a wrench or directly by hand.
• Plastic feet and rear rollers must touch the ground to pre-
vent the refrigerator from movement, vibration or noise.
When moving the refrigerator, adjust plastic feet counter-
clockwise to keep them off the ground, and then push the
refrigerator gently to move it.
Operation
Before Using
Remove all packages, including the foam backing at the bottom
of refrigerator and the tapes fixing accessories in the box. Place
the refrigerator to a proper position, and adjust the feet to level.
It is better to clean the refrigerator before use. Remove the film:
There is a layer of transparent film on the panel of our product,
which can protect products from being scratched in the process
of production and transportation, and you can choose to reserve
or remove the film as needed.
Place the refrigerator and adjust to level, clean it, let the refrig-
erator stand for above 2 ~ 6 hours, and then power on to ensure
that the refrigerator can operate normally.
Water supply connection
Warning: connect to potable water supply only.
The water supply system must be installed and connected by a
professional technician.
Connect the refrigerator with the cold water pipe:
• Min. pressure: 1.4bar
• Max. presure: 6.9bar
When using the function of ice maker, please make sure that the
tap water pipe is connected normally and the water valve is
opened. Enough space shall be reserved for the faucet connect-
ing water source.
After the refrigerator operates stably, the ice maker will make
ice. Upon power-on for the first time, cold water is available af-
ter 5 hours since the refrigerator operates normally, and ice cu-
bes or crushed ice is available after 12 hours.
Starting
Connect the power cord, and turn on the power switch.
Upon startup for the first time, the screen will display respective
set temperature values (the temperature of refrigerating cham-
ber is set as 5°C, temperature of freezing chamber -18°C).
Control panel
F-chamber temperature setting
The default temperature of the freezer is -18°C .To change the
temperature press the FRZ.TEMP button to cycle through the set
temperatures: minus -15 - 16 -17 -18 -19 -20 -21 -22 -23~ -23 +
(Super freezer) ~ -15°C.
CAUTION: Do not put fresh roods directly on the frozen foods.
R-chamber temperature setting
The default temperature of the fridge is 2°C .To change the tem-
perature press the REF.TEMP button to cycle through the set
temperatures: Plus 8 - 7 - 6 - 5 - 3 - 2 – 2°C+ (Super fridge) ~ 8°C
Display lock
This product has button lock function.
When lock the control panel, the other buttons are inoperable, if
touch other buttons, REF.TEMP and FRZ.TEMP icon will flash.
To exit lock mode, press and hold the lock button for 3s.
Open door alarm
When the refrigerator door is open for above 1 min, the buzzer
will alarm to remind users to close the door. After the door is
closed, the alarm sound will stop automatically.