background image

51

RADIATOR & ENGINE BRACKETS

1

482308

Radiator

2

481742

Hose, Upper Radiator

3

482366

Hose, Lower Radiator

4

423379

Shroud, Fan

5

04010-26

Screw. #10-32 x 1/2”

6

**

Coolant Tank Assembly w/hose (Not Avail.
Through Scag, Contact Briggs & Stratton)

7

423639

Support Bracket, Hood

8

481284

Bumper, Rubber

9

04019-03

Nut, Serrated Flange 5/16-18

10

48136-12

Clamp, 1-1/2” Dia.

11

451486

Hood Weldment

12

422703

Hinge, Hood

13

482404

Muffler with Guard

14

423640

Brace, Muffler Support

15

423637

Mounting Bracket, Hood

16

451487

Mounting Bracket Weldment, Rear Engine Mount

17

482363

Engine ISO Mount, Rear

18

04001-145 Bolt, Hex Head 1/2-13 x 3-1/2”

19

04030-06

Lockwasher, 1/2” Spring

20

04041-33

Flatwasher, 1/2-.531 x 2.0 x .25

21

482403

Manifold Extension, Exhaust

22

423381

Mounting Bracket, Engine

23

451403

Mounting Bracket Weldment, Engine L.H.

24

423382

Mounting Bracket, Engine L.H.

25

482362

Engine ISO Mount, Front

26

04041-33

Flatwasher, 1/2-.531 x 2.0 x .25

27

482270

Engine, Briggs & Stratton 31hp Diesel
(Spec. # ) Not Available Through Scag, Contact
Briggs & Stratton

28

04021-07

Nut, Elastic Stop 1/2-13

29

482602

Bushing, Radiator Isolator

30

43621

Bushing, Radiator ISO Mount

31

423638

Support Bracket, Radiator

32

423383

Mounting Bracket, Engine R.H.

33

451404

Mounting Bracket Weldment, Engine R.H.

34

423424

Mounting Bracket, Water Seperator

35

451083

Debris Screen

36

482368

Hose, Air Intake

37

482405

Air Cleaner Assembly w/mounting Band

38

481816

Pre Cleaner, Engine Air

39

481924

Adapter, Pre Cleaner

40

481818

Indicator, Air Cleaner

41

423915

Bracket, Air Cleaner

42

48136-15

Clamp, Hose 2-1/2” Dia.

43

**

Fuel Filter, Water Seperator
(Not Avail. Through Scag)

44

04001-08

Bolt, Hex Head 5/16-18 x 3/4”

45

04001-52

Bolt, Hex Head 1/2-13 x 2-1/2”

46

481827

Elbow, Exhaust

47

04002-01

Bolt, Hex Head M8-1.25 x 3mm

48

04001-32

Bolt, Hex Head 3/8-16 x 1-1/4”

Ref. Part
No. No.

Description

49

04017-16

Bolt, Hex Head 5/16-18 x 3/4”

50

423641

Catch Bracket, Hood Latch

51

04001-32

Bolt, Hex Head 3/8-16 x 1-1/4”

52

04041-07

Flatwasher, 3/8-.391 x .938 x .105

53

04041-32

Flatwasher, 1/2-.531 x 2.13 x .1345

54

04003-04

Bolt, Carriage 5/16-18 x 1”

55

04021-10

Nut, Elastic Stop 5/16-18

56

482603

Rubber Isolator

57

04041-35

Flatwasher, 7/16-.469 x 2.0 x .1345

58

04021-21

Nut, Center Lock 7/16-14

59

04021-10

Nut, Elastic Stop 5/16-18

60

04003-12

Bolt, Carriage 5/16-18 x 3/4”

61

**

Bolt, (Not Available Through Scag,
Contact Briggs & Stratton)

62

04003-04

Bolt, Carriage 5/16-18 x 1”

63

04017-16

Bolt, Hex Head 5/16-18 x 3/4” Serr. Flange

64

481309

Latch, Hood

65

04010-21

Screw, #10-32 x .375

66

04031-01

Lockwasher, #10 Spring

67

04020-01

Nut, #10

68

482601

Ring, Isolator

69

04021-09

Nut, Elastic Stop 3/8-16

70

04021-01

Nut, Elastic Stop #10-32

71

04030-03

Lockwasher, 5/16 Spring

72

48633

Muffler Clamp 1-1/2” Dia.

Ref. Part
No. No.

Description

Summary of Contents for SMST-61A




































































Reviews: