background image

2

R

Section 2

2.1 ASSEMBLY INSTRUCTIONS - CUTTER 
DECK AND BLOWER COMPONENTS

- NOTE -

Use the illustrated parts list as a part number 
reference when following the assembly 
instructions.

-IMPORTANT-

When installing this grass catcher on a machine, 
one of the following Installation Kits will be needed 
to complete the installation.

SVRII-48V - Installation Kit p/n 901M 

 

SVRII-52V - Installation Kit p/n 901N 

 

SVRII-61V - Installation Kit p/n 901P

-NOTE-

When installing this catcher on a model with serial 
numbers M9500001-N0199999, a new rear belt 
cover (p/n 427917) will need to be ordered and 
installed to provide clearance for the mounting 
bracket. 

1.  Remove all packaging materials.  Lay out the 

mounting hardware and the catcher assembly parts 
for easy access.  Prepare the work area making sure 
that it is a clean and safe environment.

 WARNING

Do not operate without discharge chute, mulch 
kit, operator controlled discharge chute (OCDC), 
or entire grass catcher installed.

2.  Remove the discharge chute from the cutter deck.  

See Figure 2-2.

- NOTE -

Do not discard the discharge chute or mounting 
hardware.  The discharge chute MUST be 
reinstalled any time the grass catcher has been 
removed from the machine.

3.  Remove the right side belt cover to gain access to 

the spindle assembly. See Figure 2-2.

- NOTE -

Retain the original belt cover.  This cover MUST be 
reinstalled any time the complete catcher system 
is removed.

Height Alignment

Tool

Height Alignment

Tool

Figure 2-1. Height Alignment Tools

4.  Remove the belt and install the grass catcher pulley 

onto the spindle assembly. Make sure to mount the 
pulley 3" from the top of the deck support plate to 
the center of the groove of the bottom pulley (use 
the height alignment tools, included with this kit, for 
increased accuracy, p/n 428125, See Figure 2-1). 
Install the pulley with the hub inverted, using 1/4-20 
x 2½" bolts (p/n 04001-225). See Figure 2-2. (The 
height alignment tools may "push out" as the pulley 
is tightened to the hub, this is normal)

REMOVE DISCHARGE
CHUTE AND 
HARDWARE

RIGHT SIDE OF

CUTTER DECK SHOWN

(Note: Some parts not shown for viewing purposes.) 

REMOVE EXISTING 
RT. SIDE BELT 
COVER

INSTALL NEW PULLEY
ON RH SPINDLE SHAFT
MAKE SURE TO MOUNT PULLEY 3”
FROM TOP OF DECK SUPPORT PLATE
TO PULLEY GROOVE OF BOTTOM PULLEY.

INVERT HUB

1/4-20 x 2-1/2” Bolt
Torque to 75 in. lbs.

Figure 2-2. Discharge Chute Removal

5.  Remove the turbo baffle from the cutter deck.  Using 

5/16-18 x 1" bolts (p/n 04001-09), 5/16 flatwasher 
(p/n 04040-15), and 5/16 elastic stop nuts (p/n 
04021-10) install the catcher turbo baffle. See Figure 
2-3. (baffles have p/n's on them)

Summary of Contents for GC-VRII


























Reviews: