CIRCUIT FINDER
Br
eaker
ID
CIRCUIT FINDER
RECEIVER
Breaker ID
Circuit Breaker Finder
1. EQUIPMENT RATINGS
• 110–120 V AC, 60 Hz, 3 w maximum.
• This device posseses a single input/output connection designed
to plug into a standard U.S. outlet.
• This device is for indoor use only.
If the device is used in a manner not specified here, then the
protection provided by the device may be impaired.
No part of this device may be replaced or repaired by anyone
except the manufacturer.
Technical assistance: 1-800-245-9265, [email protected],
or www.zircon.com.
2. INSTALLING THE BATTERY
Lift tab on bottom end of clip to release end cap.
Slide 9-V battery into compartment, terminal side
first, matching (+) and (-) terminals from battery
to case.
Slide the clip onto
the receiver, pressing
down on battery
until both pieces
snap together.
3. LOCATING A CIRCUIT
Note: A small percentage of circuit boxes are mounted
with breakers oriented vertically. See diagrams for
proper receiver orientation.
Warning: For indoor use only on standard 110–120 V
AC outlets.
Plug the transmitter into the outlet that needs to be turned off.
Verify that the red LED glows, indicating a live circuit.
Go to the circuit panel. Turn on the receiver
and hold it against the breaker as shown.
5. HELPFUL HINTS
It is important to hold the receiver at an angle so that the entire
CONTACT AREA of the receiver touches each circuit breaker.
Slowly scan the receiver over all breakers. This calibrates the unit.
During this first pass while the unit is calibrating, the receiver
may indicate more than one breaker. This is normal. If you have
more than one panel, be sure to perform this step on each panel.
Do not turn off the receiver.
Perform a second pass over the breakers.
When the green
LED glows and the buzzer sounds, you are directly over the
breaker connected to the transmitter.
Turn off the breaker.
Verify that the red LED on the transmitter is off, indicating a dead
circuit, before beginning work.
4. CLEANING AND STORING THE UNIT
Clean transmitter with dry cloth only. Do not expose product
to liquids.
Snap the transmitter and receiver together for storage.
Situation
Probable Causes
Solutions
No indication, i.e., no
green LED and buzzer.
Multiple indications on
second scan.
Tracing circuit connected
to light fixture.
Receiver indicates
breaker above the
correct one.
The breaker for that circuit is
not in the box being scanned.
The first scan was performed
too quickly.
Receiver is held horizontally
with only the tip of the receiver
contacting the breaker and
not an angle (see illustration
in Step 3).
Scan the box that supplies
that circuit.
Scan again, moving the receiver
slowly. Be sure to keep the nose of
the receiver close to the breaker
and maintain proper orientation.
Use an outlet adapter. Screw the
adapter into the socket, then plug
the transmitter into it. Or plug an
extension cord into the adapter,
then plug the transmitter into the
extension cord.
Hold the receiver at an angle so
the entire CONTACT AREA of
the receiver touches each circuit
breaker (see illustration in Step 3).
LIMITED 1 YEAR WARRANTY
Zircon Corporation, (“Zircon”) warrants this product to be free from defects in materials and workmanship
for one years from the date of purchase. Any in-warranty defective product returned to Zircon*, freight
prepaid with proof of purchase date and $5.00 to cover postage and handling, will be repaired or replaced
at Zircon’s option. This warranty is limited to the electronic circuitry and original case of the product
and specifically excludes damage caused by abuse, unreasonable use or neglect. This warranty is in lieu
of all other warranties, express or implied, and no other representations or claims of any nature shall
bind or obligate Zircon. Any implied warranties applicable to this product are limited to the one year
period following its purchase. IN NO EVENT WILL ZIRCON BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM POSSESSION, USE OR MALFUNCTION OF THIS PRODUCT.
In accordance with government regulations, you are advised that: (i) some states do not allow limitations
on how long an implied warranty lasts and/or the exclusion or limitation of incidental or consequential
damages, so the above limitations and/or exclusions may not apply to you, and further (ii) this warranty
gives you specific legal rights and you may also have other rights which vary from state to state.
Return product freight prepaid with proof of purchase date (dated sales receipt) and $5.00 to cover postage
and handling, to:
Zircon Corporation
*Attn: Returns Department
1580 Dell Avenue
Campbell, CA 95008-6992 USA
Be sure to include your name and return address. Out of warranty service and repair, where proof of
purchase is not provided, shall be returned with repairs charged C.O.D. Allow 4 to 6 weeks for delivery.
Customer Service, 1-800-245-9265 or 1-408-963-4550
Monday–Friday, 8:00 a.m. to 5:00 p.m. PDT
www.zircon.com • [email protected]
U.S. Patents 6291970 and 6933712, Canadian Patent 2353156 and Patent Pending, E.U. Patent Pending
©2010 Zircon Corporation • P/N 64267 • Rev A 04/10
Visit www.zircon.com/support
for the most current instructions.
Zircon is a registered trademark of Zircon Corporation.
Locating a breaker when you have to turn off a circuit can be a
real problem. Take the guess work out of finding the right breaker.
YES
NO
Transmitter
Receiver
Green LED
Red LED
Red LED
Vertical Breakers
Vertical Breakers
Horizontal Breakers
Horizontal Breakers
Orientation Label Underside of Receiver
ON/OFF
