background image

1

1.1 INTRODUCTION

This manual has been prepared to provide the

information you need to correctly assemble, operate,

and maintain this grass catcher. Read it carefully and

keep it for future reference.

The replacement of any part on this product by other

than the manufacturer's authorized replacement part

may adversely affect the performance, durability or

safety of this product.

USE OF OTHER THAN ORIGINAL SCAG

REPLACEMENT PARTS WILL VOID THE

WARRANTY.

If additional information or service is needed that is

not outlined in this manual, please contact your Scag

Power Equipment dealer.  Scag dealers are trained in

the latest service methods and carry a full line of Scag

replacement parts.

When ordering parts, always provide the complete

model number of your catcher.

All information provided in this manual is based upon

information available at the time of printing.  Scag

Power Equipment reserves the right to make changes

at any time without notice or obligation.

2.1 SAFETY AND OPERATING
       INSTRUCTIONS

-Note-

To  avoid  personal  injury,  it  is  imperative  that  all

safety instructions be observed.

1.

Read this operator's manual and the

operator's manual that is supplied with the

machine this attachment is used on.

A replacement manual is available from your

authorized Scag Service Dealer or by contacting:

Scag Power Equipment, Service Department at P.O.

Box 152, Mayville, WI 53050.  You may also contact

us through our website at www.scag.com Please

indicate the complete model and number of your

Scag product when ordering a replacement manual.

1.2 DIRECTION REFERENCE

The "Right" and "Left", "Front" and "Rear" of the

machine are referenced from the normal operating

position.

2. Before removing the grass bags, disengage the

mower, stop the engine and wait for all

movement to stop.

3.

ALWAYS 

turn the engine 

OFF

, remove the key

and wait for all movement to stop before

servicing or cleaning the mower or the grass

catcher.

4. Do not modify or alter any component of the

grass catcher attachment or mower.

5. Do not allow any passengers to ride on the grass

catcher attachment or on the mower.

WARNING

WARNING

DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING
KIT, OR ENTIRE GRASS CATCHER INSTALLED

Summary of Contents for GC-STC




















Reviews: