background image

4

9. Install the belt to the spindle pulley.  When

replacing the belt, see figure below.

10. Install the new belt covers and secure.  See

items number 1 and number 21 on page 9 of the

Blower Mounting Components secton in the

Illustrated Parts List for proper installation.

11. Install the hopper mounting brackets to the

outside of the frame on the rear of the machine.

See Figure 4.

Figure  4

12. Attach the hood assembly to the machine by

installing the mounting post into the hopper

mounting brackets and secure with the ring pins.

See Figure 5.

Figure  5

13. Install the hose from the blower assembly

adapter to the hopper hood and secure using the

6-1/2" clamps.

14. Install the bag assemblies.

15. Using the weight support bar as a guide, identify

the four corresponding mounting holes, and the

existing hardware that will need to be removed

in order to secure the weight support bar to the

front of the machine as shown. See Figure 5-A.

16. Install one 7/16-14 x 1-3/4" hex head bolt into

each of the four mounting holes in the weight

support bar, and through the matching holes in

the caster support weldment. Secure this

assembly to the front of the machine using the

7/16- .5" x 1-1/4" x .083" flatwashers, and the

7/16-14 elastic stop nuts. Torque hardware to

59 ft. lbs. See Figure 5-A.

FRONT SIDE
IDLER PULLEY

BACK SIDE
IDLER PULLEY

BLOWER
PULLEY

SPINDLE
PULLEY

Figure 4 A GC-STT Install Art

Hopper
Mounting
Brackets

Rear Frame

Figure  5-A

17. Operate and test.

Summary of Contents for GC-STC




















Reviews: