background image

7

Figure 13

Figure 14

Mounting ring

Mounting 

plate

Screws

11. INSTALLING THE 

LIGHT KIT 

NOTE: 

Before 

starting 

installation, 

disconnect  the  power  by  turning  off  the 
circuit  breaker  or  removing  the  fuse  at 
fuse box. Turning power off using the fan 
switch  is  not  sufficient  to  prevent  electric 
shock.

1. Remove the screws from the mounting 
plate under the fan motor.

2.    While  holding  the  switch  housing 
under  your  fan,  snap  together  the  wire 
connection plug. (Fig. 14)

3. Raise the light kit to the mounting plate 
until  the  holes  in  light  kit  and  mounting 
plate  line  up.  Reinsert  screws  to  secure  in 
place. (Fig. 14)

Mounting 

plate

Connection plugs

Light kit

Screws

10. INSTALLATING THE 

MOUNTING PLATE

1.  Remove  the  1  of  3  screws  from  the 

mounting  ring  and  loosen  the  other  2 
screws. (Do not remove)

2.  Place  the  key  holes  on  the  mounting 

plate  over  the  2  screws  previously 
loosened  from  the  mounting  ring,  turn 
mounting plate until it locks in place at 
the  narrow  section  of  the  key  holes. 
Secure  by  tightening  the  2  screws 
previously  loosened  and  the  one 
previously removed. (Fig. 13)

Summary of Contents for 52P-646-5RV-187












Reviews: