background image

8

Figure 15

Light kit

Bulbs

Pull chains

Glass shade

Decorative nut

Glass cap

Metal nut

13. FAN WITHOUT LIGHT 

KIT 

(OPTIONAL)

1. Disassemble the switch housing from 
the light kit by removing nut and washer 
on the center of switch housing, you can 
keep the light kit for future use.

2. Attach the plastic plug to the switch 
housing. (Fig. 16)

3. While holding the switch housing under 
your fan, snap together the wire 
connection plug. (Fig. 16)

4. Install the switch housing to the 
mounting plate with screws provided. (Fig. 
16 )

Figure 16

Plastic plug

Mounting 
plate

Connection plugs

Switch housing

Screws

12. INSTALLING THE 

LIGHT BULBS & GLASS 
SHADE  

NOTE:

 Before starting installation, discon-

nect the power by turning off the circuit 
breaker or removing the fuse at fuse box. 
Turning power off using the fan switch is 
not sufficient to prevent electric shock.

1. Install 3 x 40W candelabra bulbs 

(included). 

2. Insert the fan pull chain through the 

eyelet in the shade and cap. Also insert 
the light kit pull chain through the 
shade and cap. (Fig. 15)

3.  Remove the metal nut, glass cap and 

decorative nut from the light kit. Place 
glass shade over the light kit stem, 
secure with the metal nut (rubber side 
on the top), glass cap and decorative 
nut. Do not overtighten. (Fig. 15)

Note:

 Make sure to leave enough space 

between the fan pull chain and the bulbs 
so the chain doesn't rub against any of the 
bulbs.

Summary of Contents for 52P-646-5RV-187












Reviews: