Saunier Duval Themaclassic F30E PLUS Instructions For Use Installation And Servicing Download Page 1

11442

Hepworth Heating Ltd.,

Nottingham Road, Belper, Derbyshire. DE56 1JT

General/Sales enquiries:

Tel: (01773) 824141  Fax: (01773) 820569

One Contact Local Service

Customer Services:

Tel: (01773) 828100

Fax: (01773) 828070

4000122704-1.05.02

This is a Cat I

2H

 Appliance

T o  b e   l e f t   w i t h   t h e   u s e r

Instructions for Use

Installation and Servicing

Themaclassic

F30E

Fanned Flue Combination Boiler

G.C. No. 47 - 920 - 36

Guarantee Registration

The instructions consist of three parts, User, Installation and Servicing Instructions, which includes the Guarantee Registration

Card.  The instructions are an integral part of the appliance and must, to comply with the current issue of the Gas Safety

(Installation and Use) Regulations, be handed to the user on completion of the installation.

REGISTER YOUR SAUNIER DUVAL APPLIANCE

CALL 0208 247 9857

Thank you for installing a new Saunier Duval appliance in your home.

Saunier Duval appliances' are manufactured to the very highest standard so we are pleased to offer our customers’ a

Comprehensive Guarantee.

This product is guaranteed for 24 months from the date of installation or 30 months from the date of manufacture,

whichever is the shorter, for parts.  In addition this product is guaranteed for 12 months from the date of intallation or

18 months from the date of manufacture, whichever is the shorter,  for labour.

The second year of the parts guarantee,  from the beginning of the 13th month onwards after installation or

manufacture,  is conditional upon the boiler having been serviced by a CORGI registered gas installer,  in accordance

with the manufacturer's recommendations. We strongly recommend regular servicing of your gas appliance, but where

the condition is not met, any chargeable spare parts or components issued within the applicable guarantee period still

benefit from a 12 month warranty from the date of issue by the manufacturer.

We recommend you complete and return as soon as possible your guarantee registration return literature, supplied in

the document envelope.

If your guarantee registration return literature is missing you can obtain a copy or record your registration by

telephoning the Heatcall Customer Service number 01773 828100.

Themaclassic

F30E SB

System Boiler

G.C. No. 41 - 920 - 45

Summary of Contents for Themaclassic F30E PLUS





















































Reviews: