Saunders M-VUE Installation, Operation And Maintenance Manual Download Page 12 | Manualshive

Page: 12 / 32

background image

12

Calibration

Feature

P2P

AS-Interface

DeviceNet

Integral Solenoid Remote Solenoid Integral Solenoid Remote Solenoid Integral Solenoid Remote Solenoid

Self-

Calibration

At the sensor (Locally)

Yes

No

Yes

Yes

Yes

Yes

Remote (DCS or PLC)

No

No

Yes

Yes

Yes

Yes

Address Device

At the sensor (Locally)

No

No

No

No

Yes

Yes

Remote (DCS or PLC)

No

No

Yes

Yes

Yes

Yes

Programming

M-VUE

At the sensor (Locally)

Yes

Yes

Yes

Yes

Yes

Yes

Remote (DCS or PLC)

No

No

Yes

Yes

Yes

Yes

Alarm

Diagnostics

At the sensor (Locally)

Yes

Yes

Yes

Yes

Yes

Yes

Remote (DCS or PLC)

No

No

Yes

Yes

Yes

Yes

Calibration and Setting Options

The features of M-VUE are dependent on both the network/communication protocol
and the use of integral or remote solenoid.

The table below outlines the possibilities of each of the M-VUE network protocols

Description of LEDs

LED Functions:

• P1: Self Calibration
• P2: Hand Calibration
• P3: Solenoid Option
• P4: Output Inversion
• P5: Led Inversion
• P6: Factory Reset
• H1 Led: Light blue

(when magnetic key is present)

• H2 Led: Light blue

(when magnetic key is present)

• Power Led:

• Light green when power is applied

to sensor

• AS-Interface and DeviceNet versions:

• Blinking green: Not allocated
• Light red: No communication

established

• Blinking green/red: Peripheral failure

www.cranecpe.com

Crane ChemPharma & Energy

«
...
10
11
12
13
14
...
»

Summary of Contents for M-VUE

































Reviews:

No comments

Related manuals for M-VUE

Brand: Abicor Binzel Pages: 8

Line FP7000 Housing

Brand: Fantasea Pages: 5

Brand: Fantasea Pages: 5

Brand: Fancom Pages: 49

Brand: FANATEC Pages: 2

Brand: ibis Pages: 12

Brand: IAME Pages: 17

Brand: RaceChip Pages: 20

Brand: UltraGauge Pages: 55

Brand: ZARD Pages: 2

Brand: Nanoleaf Pages: 14

Brand: VARIZOOM Pages: 5

Brand: VARIZOOM Pages: 5

Brand: Yamaha Pages: 33

Brand: Yamaha Pages: 17

Brand: pleasant hearth Pages: 52

Brand: Mahindra Pages: 25

NexSys iON 24-L1-20-4.7

Brand: EnerSys Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands