satron VG Installation And Setting-Up Instructions Download Page 1 | Manualshive

Page: 1 / 20

background image

SATRON VG pressure transmitter

Installation and Setting-Up Instructions

Spare Parts List

Contents:

1 INSTALLATION

1.1 Mechanical installation
1.2 Electrical connections

2 SETTING UP

2.1 Using the 275 user interface
2.2 Setting up through HART® 275 user interface
2.3 Setting up with Satron-pAdvisor Service Software
2.4 Setting up with local switches
2.5 Set-up calibration

3

CALIBRATION

3.1 Adjustability
3.2 Damping
3.3 Calibration examples

4 CONSTRUCTION AND OPERATION

5 PARTS LIST

DOCUMENTS

Technical Specifications:

BPLV700

Installation and Setting-Up Instructions:

BPLV700AV

BPLV700AV

Man.rev.

2

2006-12-19

Satron Instruments Inc.

P.O.Box 22, FIN-33901 Tampere, Finland

Tel.int. +358 207 464 800, T358 207 464 801

www.satron.com, [email protected]

We reserve the right for technical modifications without prior notice.
HART® is a registered trademark of HART Communication Foundation.
Pasve™ is a trademark of Satron Instruments Inc.
Hastelloy® is the registered trademark of Haynes International.
Viton® is the registered trademark of DuPont Down Elastomers.

1
2
3
...
»

Summary of Contents for VG





















Reviews:

No comments

Related manuals for VG

Brand: Icom Pages: 4

Brand: Yaesu Pages: 120

Brand: Guangzhou Chuanzhou Electronic Technology Pages: 12

RFX-RMT-II Dual Band SD/HD

Brand: RF Central Pages: 38

Mini-LCD Transmitter TX-MLCD

Brand: AMX Pages: 22

Brand: Radionode Pages: 20

Brand: Icom Pages: 2

Brand: American Fibertek Pages: 4

Brand: Lodar Pages: 5

HDMI-GIGALAN-RX

Brand: Spatz Pages: 12

FMT 380 BT CHARGE

Brand: Hyundai Pages: 24

Brand: ZiFiSense Pages: 11

Brand: Questtel Pages: 13

W-DMX Micro T-1 TRX G5

Brand: Chauvet Professional Pages: 15

Brand: F.u.n.k.e. Pages: 81

Brand: Icom Pages: 50

Brand: Wulfsberg Pages: 40

Brand: SVS Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands