manualshive.com logo in svg

Satec 3100 Series, User Manual

Share
Download
Satec 3100 Series User Manual Download Page 24

Series 3100

PP3123-03-0101

Automatic Burst Test Systems

User’s Guide

SATEC PIPE & PRESSURE

24

To perform an 

FM burst test

:

1.

 

Press the Page button until “

Prog

” is displayed.

2.

 

Press the Scroll button until “

tGt

” is displayed.  This is the target pressure

value in psi.  Use the Up/Down buttons to adjust the value as desired.  The
display will blink to show that the new value is accepted.

3.

 

Press the Scroll button until “

dur

” is displayed.  This is the test duration in

seconds.  Use the Up/Down buttons to adjust the value as desired.  The display
will blink to show that the new value is accepted.

4.

 

Press the Scroll button until segment 2 is displayed.  Press the Scroll button
again to display the current parameter type.  Use the Up/Down buttons to
adjust the type to “

dwEll

”.

5.

 

Press the Scroll button until “

dwEll

” is displayed in the upper readout.  This is

the dwell time in seconds.  Use the Up/Down buttons to adjust the value as
desired.

6.

 

Press the Scroll button until segment 3 is displayed.  Press the Scroll button
again to display the current parameter type.  The parameter type should be
“

End

”.  If it is not “

End

”, use the Up/Down buttons to adjust the type to

“

End

”.

7.

 

Press the Scroll button to check the setpoint value for the “

End

” parameter.  It

should be “

rSEt

”.

8.

 

Press Page and Scroll simultaneously to return to the 

Home

 display.

NOTE:

You can get back to the 

Home

 display any time by pressing the Page and

Scroll buttons simultaneously.  Also, the 

Home

 display will return if no

button is pressed for 45 seconds (10 seconds if the controller is indicating
an alarm condition) or whenever the power is turned on.

Temporary Adjustment of Setpoint

When a program is not running, the setpoint can be temporarily adjusted by
pressing the Up or Down buttons as appropriate.  This does not change the
programmed setpoint for a test.

Summary of Contents for 3100 Series
































Reviews:

No comments

Brands by name

Popular brands

Load more brands