Satchwell IAC 600 Manual Download

Page: 21 / 24

Fig.12

IAC TOUCH-SCREENS AND BASE UNITS ON A LAN

REMOTE MOUNTED TOUCH-SCREEN USING KIT
565-2-601

REMOTE MOUNTED TOUCH-SCREEN USING KIT
565-2-601 CONNECTED DIRECT TO IAC 200, 400,
420 AND 600s

Fig.14

Fig.15

LAN from
PC or MIU

RS422/
485

Up to 31 Networking Controllers and 1000m, more (up to 95 controllers on the MAIN LAN, and

another 1000m) if an MIU is used as a repeater.

IAC BASE UNITS ON A LAN (NO TOUCH-SCREENS)

LAN
from PC
or MIU

RS422/485

Touch-screen
addresses 65
to 95

Up to 31
Touch-
screens

More IACs

RS422/485

Addresses 1 to
31 must not be
used on the
main LAN as
they are
reserved for
use on the
sub-LAN.

To further
Networking
Controllers
(Address range 1
to 63, MIU required if total
number is greater than 31)

Fig.13a

Fig.13

DETAIL OF LAN SCREENING

Screen

Up to 30* IAC 200/400/420/600s and 1000m

Controllers (including MIUs) on the main LAN and sub-LAN must not have conflicting

addresses. Controllers on different sub-LANs may use the same address. Ideally the sub-LAN

addresses should be kept within a range so as not to use up all of the main LAN addresses.

The number of IAC controllers on a Touch-screen
Sub-LAN is limited to a maximum of 31 base units
including the one the Touch-screen is plugged into.
Each Touch-screen can display up to 256
parameters.

ISOLATED
GROUND

LAN A and LAN B should be screened with the screen earthed only on a verified good earth at the computer or MIU.

LAN A and B screens should be connected to the isolated Ground Terminals of each of the IACs on the LAN - see Fig.8.

LAN A and LAN B should be screened with the screen earthed only on a verified good earth at the computer or MIU.

LAN A and B screens should be connected to the isolated Ground Terminals of each of the IACs on the LAN - see Fig.8.

Remote
Touch-screen
Adaptor Kit
565-2-601

To other
IAC 200,
400, 420
and 600
controllers
on the
sub-LAN

IAC 600
Base

Screen

To computer
or MIU

If greater than
50m use 24
Volt Supply
local to the
Touch-screen

Note:- Maximum cable length from the computer/MIU
via the IAC 600 base to the Touch-screen is 1000m.

TOUCH-SCREEN

Remote
Touch-screen
Adaptor Kit
565-2-601

TOUCH-SCREEN

To IAC 200,
400, 420
and 600
controllers

To computer
or MIU

IAC 600
Base

Supply

Note:- Maximum cable length from the
computer/MIU to the Touch-screen is 1000m.

SUB-LAN

05/98

21 - 24

DS 2.951A

Summary of Contents for IAC 600

























Search results

Summary of Contents for IAC 600

Reviews:

Related manuals for IAC 600

Brands by name

Popular brands

Satchwell IAC 600, Manual

Search results

Summary of Contents for IAC 600

Reviews:

Related manuals for IAC 600

Brands by name

Popular brands