17
The signal after “time out” will stay 7 minutes if it has not been reset with “time of day” button.
The following signal will be skipped if time of day is pressed during the last 15 seconds of the timer.
Signal frequency
If no function is activated, the signal frequency can be selected by pressing the "-" button.
Three different frequencies (1,5 ; 2,0 ; 3,0kHz) are selectable.
USING THE TOUCH CLOCK (Fig.54)
Mains frequency detection
At power on mains frequency is determined. When the timer is connected to 60Hz, the Celsius symbol is flashing during start-
up.
Power On
At power on, the relay contact is opened. The display and AUTO symbol flashes and time of day starts from 0:00. Power on
state with flashing daytime remains until time of day is set
.
Setting Time of Day
Press PLUS and MINUS button simultaneously. At Power On, also MODE button is possible.
Time of day can be set with PLUS or MINUS, while the colon between hours and minutes is flashing.
Quick setting mode starts when PLUS or MINUS is held for more than 1 second. If daytime setting mode is selected while an
automatic program is active, the automatic program is cancelled.
The Buzzer
The buzzer interval alarm signal sounds if minute minder has reached the end time. The signal can be switched off by pressing
any key or by passing the signal duration limit
.
Changing the Buzzer frequency
First
press Plus and Minus simultaneously (menu far editing the time) and then Mode for selecting the menu far changing the
buzzer frequency. While the text is visible the buzzer signal frequency can be changed by touching Minus repetitively.
Note: If the touch pad is inactive, a visual alarm will only be reset when a valid key combination is pressed far more than 2
seconds.
Clearing Programs and Manual function
The duration of the minute minder can be cleared by
a)
"clear Function":
First select minute minder program, then press PLUS and MINUS button simultaneously.
a
fter this clear the display returns from adjustment mode to time of day immediately
.
b)
B
ack counting of duration to zero. The timer remains in adjustment mode.
Minute Minder
While
minute minder mode is selected, the Bell symbol flashes and the display reads the remaining time in hours and minutes,
only if the last minute is counting down the remaining seconds are displayed. An active minute minder program is
i
ndicated by
the stat
ic
ally illuminated Bell symbol
.
If alarm time has f
i
nished, an acoustic interval signal sounds and the Bell symbol flashes.
The minute minder program runs
i
ndependently of other programs.
Key Lock
After power on reset or when no key is pressed for 7 seconds, the key look function is act
i
vated. Pressing a valid key or key
combination for 2 seconds or more will deactivate the key lock.
USING THE ANALOG CLOCK (Fig.55)
For setting up the time displayed by watch pointers push briefly twice the knob till getting the CLOCK icon flashing.
For increasing or decreasing time displayed 1 minute by 1, turn the knob clockwise or counterclockwise, le minutes pointer will
increase or decrease 1 minute by minute clockwise or counterclockwise.10 seconds after last set up the electronic timer will exit
time set up mode.Minute minder set up will activate a simple alarm when set up time is over.
For setting up an alarm push briefly once the knob till getting ALARM icon flashing. The turn the knob, set up the alarm time and
briefly push once the knob to confirm; ALARM icon will stay on for all the set up time. When set up time is over an acoustic buzz
will be activated. Push again briefly once the knob for going back to time display.
For cancelling minute minder set up keep the knob pushed until ALARM icon goes off.
ELECTRONIC TIMER
PROGRAMMER
(Fig. 56)
Setting
Select a function by pressing the function button and set the required time with the +/- buttons.
+/- buttons
Pressing the “+” button increases the time set, pressing “-“ decreases it. The count-up and countdown speed increases the
longer the button is held in the appropriate position
Setting the time of day
Select the time of day function by pressing the duration and end time button together and set the time of day with the +/-
buttons.
Any programme which has been set is cancelled and the outputs switched on
Manual operation
Press duration and end time button together. The relay contacts will switch on. The “A” symbol will be erased, the pot symbol
illuminated. Any programme which has been set is cancelled.
Semi-automatic operation with cooking duration
Select the cooking duration function and set the required duration with +/- button. “A” and cookpot symbol appear. The relay
output becomes active. If time of day = cooking end time the relay output and the cookpot symbol are switched off.
The audible signal sounds. The symbol “A” blinks.
Semi-automatic operation with cooking end time
Summary of Contents for TS95C61LNE
