background image

1  Template 

Instructions 

<<Delete before 
use>> 

 

EC

60

0

 

 

 

             EC600 Power Control System 

 

 

 

 

Issue 2.3 

Page 17 of 20 

10

th

 August 2017 

Fault 

Possible Cause 

Proposed Fix 

Reverse Polarity 

light is 

illuminated on 

PSU 

Mains Supply reversed? 

The reverse polarity light is designed to illuminate when the Live and 
Neutral supply has been reversed / crossed over. If the light 
illuminates there is a problem with the site supply or the cable 
connecting the supply to your vehicle. The light is designed to work 
on UK electrical supplies (where the neutral conductor is connected 
to earth at the sub station). If you are using your vehicle outside the 
UK this light may illuminate when no fault exists. In these cases 
consult the site warden for advice. 

Generator being used 

‘The Reverse Polarity warning light is on when using my Generator’. 
This is a normal side effect when using some types of generator. 
Instead of connecting the neutral conductor to earth, some generators 
centre tap the earth connection making both neutral and live 
conductors 110V above earth. This 110V difference causes the neon 
polarity indicator to illuminate.  In most cases it is still safe to use the 
generator, but please consult the generator handbook for further 
information. 

Control Panel 

Problems 

Control Panel has no 
display 

Check batteries and fuses, turn PSU isolate switch and charger 
switch on and ensure mains supply is connected. 
Check control panel connecting lead at PSU and behind Control 
Panel. 
Contact your Dealer. 

12V Power turns off  

Battery protect feature has operated to protect the Vehicle battery 
and or the Leisure battery.  See 3.4C 
Over voltage protection has been activated, the control panel will 
display a warning. A number of things can cause this but the most 
common is the solar panel, it is worth checking the regulator is 
connected correctly and operating within the correct parameters. 
Engine has been started, all equipment has been disconnected to 
meet EMC requirements.  See 2.6 

Control Panel locked / 
erratic function 

Observe control panel handling instructions. 
Control panel software may have crashed.  Reboot control panel by 
turning off the PSU isolate switch.  Wait 30 seconds then turn the 
switch back on.  Check with your dealer that your system has the 
latest software installed, as an update may be available. 

No 12 volt output 

from PSU 

No 230V supply 

Check all above. 

Charger not switched on 

Turn charger switch on, switch will illuminate. 

Battery not connected and 
/ or charged 

Install charged battery as per 3.4 

Power button on control 
panel not switched to on 

Turn power on at control panel. 

Battery flat / Battery fuse 
blown 

Recharge battery, check fuses, check charging voltage is present at 
battery. 

Fuse blown 

Check all fuses are intact and the correct value fuse is installed as 
per fuse table.  

Equipment switched off / 
unplugged 

Check equipment is switched on and connected to the 12V supply. 

Other fault 

Contact your Dealer. 

Pump not 

working 

Fuse blown 

Replace fuse with correct value as per fuse table. 

Pump turned off 

Turn pump on by pressing the pump button at the control panel. 

Setting incorrect 

Both the internal and external pump feeds are controlled from the 
control panel. To alter the setting of the pump switch see section 3.8 
Ensure the setting matches your desired requirement. 

Lights not 

working 

Fuse/s blown 

Replace fuse with correct value as per fuse table. 

Lights turned off 

Turn Lights on by pressing the lights button, use dimmer at the 
control panel. 

Communications  Bluetooth not paired 

Using System Settings menu, select Bluetooth Pair option. 

Summary of Contents for EC600





















Reviews: