manualshive.com logo in svg

Sanyo CLT-D14, Instruction Manual, Page: 31 / 40

Share
Download
Sanyo CLT-D14 Instruction Manual Download Page 31

31

REMOTE ACCESS

During message playback:
- “ 4 ” Skip
- “ 5 ” Repeat
- “ 6 ” Rewind (previous message)
- “ 7 ” Delete current message
- “ 9 ” Pause/Resume
- “ 0 ” Stop and return to Remote Access Mode.

2 and then 1

Replay Outgoing Message 1.
During message replay, press “0” to stop
playing and return to Remote Access mode.

2 and then 2

Play Outgoing Message 2 (Announce Only
OGM)
During message replay, press “ 0 ” to stop
playing and return to Remote Access mode.

2 and then 3

Record a new Outgoing Message 1. A beep
tone will be generated to indicate the start of
the recording, You may speak the message
for recording. Press digit “ 0 ” will terminate
the recording and return to the Remote
Access Mode.

2 and then 4

Record a new Outgoing Message 2
(Announce Only message). A beep tone will
be generated to indicate the start of the
recording, You may speak the message for
recording. Press digit “ 0 ” will terminate the
recording and return to the Remote Access
Mode.

Summary of Contents for CLT-D14









































Reviews:

No comments