Sanyo 3WAY MULTI SGP-EZ150M2G2 Manual Download Page 10

Page: 10 / 34

II -

2. Periodic Inspection and Periodic Replacement Work Manual

Periodic inspections and replacements are very important for ensuring that users can enjoy long and trouble-free service

from Sanyo gas heat pump air conditioners.

(1) Engine Oil Replenishment and Oil Filter Replacement

Safety Precautions

Stopping only the indoor unit is extremely dangerous because the engine

may suddenly start if the customer operates the remote controller on the

indoor unit side. Before carrying out work on the inside of the outdoor unit,

make sure you turn off the power supply circuit breaker of the outdoor unit.

(However, if a system controller or other centralized control device is being

used, an abnormal communications error may be generated.) Alternatively,

perform the STOP operation for the outdoor unit.

● Engine and model number relationship

Engine name

Model No.

K25 (Nissan engine)

SGP-EW120/150/190/240M2G2W (W MULTI)

SGP-EZ150/190/240M2G2W (3WAY MULTI)

For details on how and when to perform engine oil inspection, replenishment and replacement, see attached table

Chapter [2 (2)].

Use Sanyo genuine oil for the engine oil.

● Idemitsu Kosan (Co., Ltd.)

Sanyo Genuine AP. GHP D-125

● Nippon Oil Corporation

Sanyo Genuine GHP Oil 10TH

● COSMO OIL LUBRICANTS Co., Ltd.

Sanyo Genuine GHP Oil 10W30C2

Engine oil and oil filter replacement period

Replace the engine oil and oil filter every five years or 10,000

operating hours, whichever comes first.

The following tools, parts, and materials are required for doing this work. Prepare them before starting:

Name

Specification

Q’ty

Remarks

s, M

Sanyo genuine oil

D-125

10TH

10W30C2

liters

·Sanyo Genuine AP. GHP D-125

·Sanyo Genuine GHP Oil 10TH

·Sanyo Genuine GHP Oil 10W30C2

Oil filter

For models with a K25 engine

638-012-7993

Waste Oil container

needed

Rags

needed

Screwdrivers

No-3 Phillips, No-2 flat

each

Closed wrench

19mm

Oil pump or hand pump

Filter wrench

Oil container with narrow

spout

5 liters

Tray (Oil drain basin)

Pliers

Figure 1 SANYO genuine gas engine oil

Summary of Contents for 3WAY MULTI SGP-EZ150M2G2



































Search results

Summary of Contents for 3WAY MULTI SGP-EZ150M2G2

Reviews:

Related manuals for 3WAY MULTI SGP-EZ150M2G2

Brands by name

Popular brands

Sanyo 3WAY MULTI SGP-EZ150M2G2, Manual

Search results

Summary of Contents for 3WAY MULTI SGP-EZ150M2G2

Reviews:

Related manuals for 3WAY MULTI SGP-EZ150M2G2

Brands by name

Popular brands