manualshive.com logo in svg

Sanyo Denki SANUPS E11A Series, User Settings Manual, Page: 10 / 35

Share
Download
Sanyo Denki SANUPS E11A Series User Settings Manual Download Page 10

 

 

 

8 

Two beeps are heard. The setting is saved and the UPS returns 

to normal operation. 

 

§

§

3

3

.

.

5

5

 

 

S

S

e

e

t

t

t

t

i

i

n

n

g

g

 

 

P

P

C

C

 

 

I

I

n

n

t

t

e

e

r

r

f

f

a

a

c

c

e

e

 

 

 

 

①

 

Check that the UPS is in the following condition. 

 

 

 
 

 

②

 

Press and hold 

  for 3 or 4 seconds. Then release it when two beeps are heard. 

 
 

 

 

 

 

 
 

 

 

 

 

③

 

Quickly press 

  (within 3 seconds) several times to set the 5 LEDs surrounded by              in the figure 

below to a blinking pattern such as the one in the figure. 

 

 

 

 

 

 

 

 

 

 

 

 

④

 

Quickly press 

  (within 3 seconds) several times to switch to the setting value LED blinking pattern 

to select for the 4 LEDs surrounded by 

  in the figure below. 

 

 

 

 

 

 

 

 

 

 

 

 
 

 

 

 

⑤

 

Press and hold 

  for 3 or 4 seconds.   

Then release it when two beeps are heard. 

 

 

 

 
 

 

 

 

LEDs that blink when the “Standalone” setting is selected. 

 
 

 

 

Setting

 

Setting LED

Description

 

Standalone

●

 

○

 

○

 

○

Set when using the following functions

・

Standard OS UPS Services 

・

UPS remote ON/OFF 

Workstation

○

 

●

 

○

 

○

Set when using the following functions

・

The power management software 

・

LAN Interface card 

・

UPS remote ON and One-touch 
system shutdown by remote switch 

Serial Login

●

 

●

 

○

 

○

Shutdown by serial login. 

－

 

○

 

○

 

●

 

○

Do not use this setting 

*1. When using 001 model, do not use this setting. 

Set the interface mode when using external 

interface connector. 

Default

setting

The blinking pattern changes each time you press 

  or 

. 

If you miss the LED blinking pattern you want to select, continue pressing 

the button repeatedly until the LED blinking pattern is redisplayed.

 

Tip

  MAIN SW    on the back panel set to “ON”. *1 

 

The “Green ON/STAND BY” and 

the “Green OUTPUT are not blinking. *2

 

*1. Operation is possible regardless of whether 

 

is ON or OFF. 

*2. If these LEDs are blinking,    Forced Bypass  switch 

may be set to “Bypass”. Set this switch to “Inverter”, 

and restart the UPS. 

 

Tip

The UPS switches to the user setting mode.

 

 

Buzzer sounds : 2 beeps

 

 

：

Either BATT.LOW or 25 

blinks,  

or both

 BATT.LOW and 25 

blink.

 

 

：

INPUT blinks. 

：

LED is off. 

：

LED is blinking.

 

Hold for 3 or 4 sec. 

until 2 beeps. 

Press

 

Press

 

Hold for 3 or 4 sec. 

until 2 beeps. 

*1

Summary of Contents for SANUPS E11A Series




































Reviews:

No comments