Sanyo Denki ASD 100S2NU Installation & Maintenance Manual Download

Page: 29 / 32

12. At sounding buzzer

The buzzer sounds when an abnormal or altered UPS condition occurs.

Note the pattern of the buzzer sound and refer to this table.

Buzzer Sound

LCD Message

Equipment Status

Measures

SERIOUS ERR!

Equipment fault

Refer to

3.4, “Displaying Alarm

Records” in the

LCD Panel Operation

Manual

, and contact your supplier.

Some bypass breakers

are switched off.

Turn on any bypass breakers that are

off. Verify the bypass breakers in all

units are on.

MINOR ERR.

Arrester fault

Refer to

3.4, “Displaying Alarm

Records” in the

LCD Panel Operation

Manual

to verify that

ART_ERR

displayed, and contact your supplier.

Continuous beep

BATTERY END!

OUTPUT STOP!

Battery discharge

terminated

When utility power is restored, the
UPS restarts automatically. (If

START

is selected as described in

3.11 of

the

LCD Panel Operation Manual

)

POWER FAILURE

BATT BACK UP OP.
INPUT HV BATTERY

BACK UP OP.!
INPUT ERR!

BATT BACK UP OP.

Five beeps, pause, five

beeps, pause, …

UNIT TROUBLE

BATT BACK UP OP.

Abnormal input voltage

or frequency; power is

supplied from battery

INPUT breaker is

switched off during

inverter power

operation

Obtain normal input voltage and

frequency.

Turn on the INPUT breaker.

POWER FAILURE

BATT VOLT. LOW!
INPUT HV BATTERY

VOLTAGE LOW!
INPUT ERR!

BATT VOLT. LOW

Beep, beep, beep, beep …

UNIT TROUBLE!

BATT VOLT. LOW!

Battery voltage is low

Obtain normal input voltage and

frequency.

Turn on the INPUT breaker.

Beep, pause, beep, pause …

(4-second intervals)

NORMAL OPERATION

Demand of loads

connected to the UPS

output exceeds rated

current capacity.

Decrease the load at the UPS output.

Beep, pause, beep, pause …

(2-second intervals)

CHECKING XXXmin

PRESS← TO STOP

Battery test in progress.

Wait for battery test to finish.

Push

to abort the battery test.

BATTERY OK XXmin

PRESS ← KEY

Four beeps

BATT NG XXmin

PRESS ← KEY

Battery test is finished.

Check the LCD to determine whether

the test finished normally or

abnormally (low battery capacity),
and push

BATT LIFE 4320H

ADVICE CHANGE!

Remaining battery

service life is a half

year.

Battery replacement is

recommended. Contact your supplier.
Push

to turn off the ALARM

(Red) LED. LCD display blanks if

there is no operation for four

minutes.

Beep, pause, beep, pause …

(0.5-second intervals)

BATT LIFE 0H

CHANGE NOW!

Battery service life has

expired.

Battery replacement is required.

Contact your supplier. Display and

ALARM (Red) LED are not reset till

the batteries replacement is finished

by technically qualified personnel.

Note

If problems occur, contact your supplier.

Push

silence the buzzer.

Summary of Contents for ASD 100S2NU

































Search results

Summary of Contents for ASD 100S2NU

Reviews:

Related manuals for ASD 100S2NU

Brands by name

Popular brands

Sanyo Denki ASD 100S2NU, Installation & Maintenance Manual

Search results

Summary of Contents for ASD 100S2NU

Reviews:

Related manuals for ASD 100S2NU

Brands by name

Popular brands