Sanitaire 680 Series Owner'S Manual Download Page 8

Page: 8 / 16

Attach Upper Cord Hook

Pull the spring on the electrical cord upward
toward the top of the handle. Make sure slots in
handle are positioned properly, see Detail B.

Insert the lower half of the spring into the upper
cord hook, as shown. Snap the hook into the
upper handle, directions below.

Cord Storage

Wrap the cord around the two cord hooks.
Fasten the plug to the cord to prevent unwinding.

Hook Bag Top

Slip the ring at the top of the cloth bag over
the bag support hook on the back of the
cord hook.

1. Place

inner tab
into slot

2. Press hook

around
handle

3. SNAP opposite

inner tab into
place

Attach Lower Cord Hook

Insert the power cord into the lower cord hook
(A), as shown. Snap the hook into the lower
handle. Pull up on the cord to tighten but leave
enough slack near the base so the cord is not
strained when the handle is lowered.

Summary of Contents for 680 Series

















Search results

Summary of Contents for 680 Series

Reviews:

Related manuals for 680 Series

Brands by name

Popular brands

Sanitaire 680 Series, Owner'S Manual

Search results

Summary of Contents for 680 Series

Reviews:

Related manuals for 680 Series

Brands by name

Popular brands