background image

8

GB

  Notes on safety

Only operate this appliance with a power supply of 220-230 Volt/
50-60 Hz . If you intend not using the appliance for a longer period of
time ( eg. Holidays), pull the plug out of the mains socket to ensure a
complete separation from the power supply.

Protect the appliance from heat and moisture.

Do not open the appliance and if it should require servicing, please
refer to a licensed electrical workshop.

  Operation

  Clock

Radio controlled clock

In normal case, please set the time zone switch 7 to 0 (UTC)
position.

When the appliance is connected to the power supply for the first
time or if it has been separated from the power supply for a longer
period of time, the radio will appear L9 or L8 or less to indicate the
strength of radio controlled signal. If the signal indication is weaker
than L7, please rotate the external antenna and if necessary extend
the external antenna to a proper position to get best signal.
Display will appear —  : —  and the symbol        will blank indicating
the radio is searching radio controlled signal. The correct time and
date will be set automatically. When the time signal is being
received, the time and date have been set correctly (after
approximate 3 minutes), the        symbol stops blinking and remains
lit indicating the time and date are with radio controlled time.

Summary of Contents for RCR-2



















Reviews: