background image

9

If the symbol        blinks irregularly, try to improve the reception of the
radio controlled time signal by re-allocating the radio, or rotate or
extend the external antenna. If the time signal can not be received in
your area, you will have to set the time and date manually.

Note :
To activate radio controlled time check manually, press Time button 9
for more than 4 seconds, the appliance will start to search radio
controlled time signal.

  Manual time setting

TIME

Press TIME button, display will flash        and previous allocated time.
Press SET button, the Hour digits in the time display begin to blink
with a beep.
1. Adjust the hour with key  + or - .
2. Press the SET button once again to confirm the hour, now the
    minute digits in the time display begin to blink.

Adjust the minutes just as you adjusted the hour:
1. Set the minutes with key + or -.
2. Press the TIME button once again to confirm the time setting with
    a beep.

The second starts to count. The     symbol will appear indicating this
is not radio controlled time.

Note:
If there is Daylight Saving Time ( D.S.T.) system in your place,
after pressing SET button, press Mode button once will
advance one hour on time setting, Display will show D.S.T.
symbol indicating the time is under D.S.T. status.

Summary of Contents for RCR-2



















Reviews: